Repairs to uPVC Windows

upvc window Repair windows are a great choice for upvc Window Repair modern homes. They are easy to maintain and are durable and long-lasting. They do not get rotten or rusty like aluminum and timber.

It is crucial to wash and oil UPVC doors and windows regularly. This will help prevent unnecessary repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it can cause a huge deal of damage to your home, which can make it very dangerous and potentially fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows, it is fairly easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this case it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.

If you are going to attempt to remove the glass panes yourself, it is essential to wear the proper safety gear such as gloves that are thick and eye protection. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards fall on the fabric and not onto the floor which could cause them to be trampled.

It's a great idea to tape the gap once the glass is removed. This will prevent water and drafts from entering your property until a professional arrives to fix the window. This will also act as a barrier, deterring any intruders from getting access to your home. If the distance between the window and the door is significant, you may prefer a security screen that also has an opening. This will provide the best of both.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. However, over time they can suffer from a variety of issues, including sliding. A sagging uPVC windows can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to stop the issue from getting worse.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to open the windows to get at the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Close your window to test the fit after you've repositioned your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they stay in position.

If you are unable to reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity with time, leading them to lose their tightness. It is crucial to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also become loose. This is often caused by screws that have loosened over time, but it can also be due to the handle mechanism wears out. Fortunately, it's easy to repair the loose uPVC window handle yourself. First, you'll need to close the window and then perform a test to ensure that it fits. The joints at the corners of the sash should be aligned with the joint on the casing. If it doesn't then you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into the position it was in.

3. Water Leaks

It is essential to take action if wake up every morning to find a smoky wall and uPVC window repair floors that are wet. Windows that leak water do can not only cause degradation of your home's structure but also hamper your efforts to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be completed by any DIYer who is competent. Depending on how severe the issue is, the old caulking may need to be removed. When it is time to uPVC repair, it is important to be careful not to over-caulk. This will make your window harder to clean and decrease its energy efficiency.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled correctly so that it drains away from the window repair. In more serious instances, you might have to consider replacing the window.

Mold spots and rotted sills are also signs of water leakage. This fungus thrives in damp conditions and can quickly spread throughout the house.

If the leakage occurs between the double-glazed window, it is more likely the issue is more with the seal rather than the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be the reason when your uPVC window is difficult to open, or if it opens with the breeze. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical component hinges are prone to wear out over time. It is essentially a simple process, but it's easier if you have someone to help you hold the frame in place.

Make sure that the uPVC hinges open and close in the correct direction. You can check this by looking for the arrow on each hinge. This indicates which way the window should open.

The issue could be caused due to opening the window in the wrong way or due to a poor installation at the factory. Sending us a picture via our website will often resolve the problem. We are always happy to give assistance.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regularly lubrication makes the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. The ideal time to perform this every year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a variety of different things. The hinges may also become unbalanced due to wear, which can cause gaps where the sash and frame meet. If they are damaged beyond repair, it might be necessary to get them re-aligned. In addition, the interlock could also become unbalanced. It is located on the hinge's side and could require to be cleaned. In some instances it might be necessary to replace the hinges.

The next common reason for draughts are the window seals, these are prone to wear or damaged over time and allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with glass that is low-emissivity, this will help to regulate indoor temperatures and will lessen draughts.

Another method of reducing drafts effectively is to use a Draught-excluder. These are usually fabric tubes filled with a filler that can be put on top of your window sill. They will help block out cold air and keep your home warm and cosy!

With a little regular maintenance and repair windows made of upvc will provide a great level of insulation and security for your home. However, it is important to recognise that all windows have a life span and there may come a point where it is more economical to replace them than repair them. If you are having issues with your upvc windows, it is recommended to seek help from a professional as soon as you can.