How to Replace a Kia Sportage Replacement Key

For a variety of Kia models the key comes with an integrated keyless entry system. This key is similar to the remote control and is exchangeable by a kia key fob dealer.

Key fobs may stop working due to a number of reasons, including the battery being dead, worn-out buttons signal interference, or water damage. Here are some tips on how you can get your Kia Sportage replacement key to work again.

How to replace the remote key or smart key?

The battery inside your Kia's smart key will eventually have to be replaced, whether it's a remote key as well as a push-to start key or a regular metal key that is not equipped with transponder. This is particularly relevant if your car displays a message indicating that the smart key or remote has low battery power.

This is a relatively easy process. To replace the battery of the key fob, remove the mechanical key from the hole in the back of the key fob. Then pry open the cover. Inside the key fob, there will be the small screw that holds the battery in the correct position. Utilizing a small screwdriver loosen the screw and pull out the battery that was in place. Then insert the new one and close the slit in the key fob.

When the key fob is equipped with an updated battery, test it by pressing the locks and unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to complete errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, it is necessary to record the key code number on the tag for the key code.

How do I replace the battery?

If the kia key (gokseong.multiiq.com) fob is unable to respond to pressing the lock/unlock button, it's likely that the battery is depleted. A low battery may cause other issues, like the check engine light flashing or the engine not cranking properly. It is quite simple to replace the key fob batteries using just two tools.

Before you begin, make sure that your vehicle is off and all doors are shut. Find the small metal or plastic piece that is located at the bottom of the key fob. Press it until the metal key pops out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and align the new one to ensure that the "+" positive side faces your face and the "-" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid bending or damaging the contacts on the metal.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks up. You can then test the Kia's key fob once more to ensure it's working as intended.

How can you replace the smart key

There is a possibility of having a standard keyfob or a Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs come with an internal battery that will eventually need to be replaced. This is a straightforward process that takes less than two minutes.

Before you start it is important to make sure that you are on a flat surface with good lighting and that your Kia is turned off. Be aware that there are tiny pieces inside the fob that could be snagged if not careful.

The first step is to find the small release button that is located on the backside of the fob. It will be either a circular silver button or a rectangular slot. After pressing this button button, the mechanical blade will be released and you will be able to open the key fob.

After the key fob has been opened, take out the battery. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. After you've finished, your key fob should permit you to lock and unlock your vehicle, even if it isn't running.

How to replace the mechanical key?

The Kia keyfob can be a fantastic convenience that lets us lock or unlock our car by simply pressing a button. However, like all devices it may have issues from time to time. There are solutions to resolve these issues and keep your key fobs functioning for many years.

A dead or drained battery is one of the most frequently encountered issues. This can cause your fob to stop working or operate intermittently. If this is the case, replace the battery with an entirely new battery.

If this does not solve the issue, you can use a standard flathead screwdriver to wedge the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced with a brand new battery.

After the new battery has been put in, close and then open the doors using the mechanical key (every Kia fob has an emergency mechanical key that will fit into the slot). Test the key fob to confirm it's functioning correctly. Contact a dealer or a locksmith to resolve the problem when the fob still is not working. Make sure they cut you an emergency key that functions for all trunk and door cylinders to avoid lockouts in the future.