How to Replace a Kia Sportage Replacement Key

The key of a lot of kia picanto key Fob replacement models has the keyless entry feature built into. The key is usually akin to the remote control and can be replaced with a brand new one from an Kia dealer or a locksmith.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons signals, signal interference, water damage and a malfunctioning receiver module. Here are some helpful tips to assist you in getting your Kia sportage replacement key working once more.

How to replace the remote key or smartkey?

It doesn't matter if your Kia is equipped with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually require replacement. This is particularly true if your car shows a message that states the smart or remote keys aren't powered.

Luckily, this is a relatively simple process. To replace the battery of the keyfob remove your mechanical key from the slot at the back of the fob. Then, pull the cover off. A small screw is in the key fob that holds the battery in the correct position. Remove the old battery by removing the screw using a small screwdriver. Install the new battery and then close the opening on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're good to go! You can now use kia sportage key fob's hands-free lock/unlock function when your fingers are cold or you have to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a particular programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder metal keys) are not required for programming. If your key requires to be reprogrammed, you must be aware of the key code written on the key code tag and save the number in a secure place.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it is likely that the battery is low. A low battery may cause other issues, such as the check engine light coming on or the engine not working correctly. Fortunately, replacing the battery on the key fob is a relatively easy DIY task that requires only some basic tools.

Before starting the process ensure that your vehicle is turned off and all doors are closed. Find the small metal or a plastic piece that is located at the bottom of the key fob. Press it until the key comes out. The key can be put into the door's driver handle to unlock your car.

To replace the key fob's battery, remove the rear cover and use a plastic bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery so that the "+" positive side is facing your face and the "-" negative side is facing towards the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After the new battery has been installed then turn the key fob off and then on in the ignition repeatedly until the door locks. Then you can test your Kia key fob to determine whether it's working again.

How to replace the smart key

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between the two is that the smart key is equipped with a small mechanical key blade tucked inside it, while the standard key fob does not. Both key fobs come with batteries that will eventually require changing. Fortunately, this is an easy task that takes just two minutes.

Be sure to turn off your Kia, and be on a flat and well-lit surface prior to you begin. Keep in mind that there are tiny parts inside the fob that could be snagged if not vigilant.

The first step is to find the small release button on the lower backside of your fob. It's either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open then you can take out the old battery and replace it. The new battery is one called CR-2032 and can be purchased on the internet or at your local auto parts shop. Once you're done, you should be able to lock, unlock and start your vehicle using your key fob even if the engine isn't running!

How to replace the mechanical key?

The Kia key fob is a wonderful convenience that lets us lock and unlock our vehicle with the click of the button. As with all devices like a key fob, the Kia can occasionally have problems. There are ways to solve these issues and keep your key fobs running for the duration of.

One of the most frequently encountered issues is a low or dead battery. The fob could be able to stop working completely or work intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't solve the issue, you can use a standard flathead screwdriver to push the fob's casing made of plastic open. Be sure not to damage any internal components or scratch the plastic. After the battery has been removed and replaced, you can replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's functioning correctly. If the fob isn't functioning, contact a dealer or locksmith to solve the issue. Make sure they cut you an emergency key that works for all trunk and door cylinders to prevent lockouts in the future.