Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's large dimensions give it an SUV feel. Its 19-inch alloy wheels on Ti and STL models may also be firm. The front tyres could lose grip on rough surfaces, and its CVT could occasionally exhibit wrist-flexing torque steer.

This is usually due to an unresponsive coin battery that can be easily replaced in just a few minutes. Make sure the new battery is of the same voltage, size and specifications.

Water Damage

One of the most frequent reasons a Nissan key fob will give the "key ID is not correct" message is due to water damage. The rubber seals on the key fob protect the chip's electronic components, however prolonged moisture exposure can cause it not to work effectively. This is usually the case in the event that you've dropped your key fob into the ocean or a pool in a pool, but it can also happen if it gets wet from soapy hands or rain.

If your key fob is exposed to water for a lengthy time, it may need to be cleaned using isopropyl alcohol or an electronic cleaner. Alternatively, it might need to be taken to a professional for repair or replacement.

If your key fob has to be replaced, it is quite simple to do. First, ensure you have a multipack of the correct battery (CR2032 3V). Open the back and front cases using the small flathead screwdriver. Remove the metal clips, take out the old battery and then replace it. Reassemble the fob and replace the mechanical key. Verify that it is working properly. If it doesn't then you'll have to take it to a nissan juke key fob replacement dealer or a professional auto locksmith to repair the key chip. The chip is not usually damaged by water so it shouldn't be too expensive.

Dead Coin Battery

Another reason why your Nissan Qashqai key fob might not work is because the battery in the coin has gone dead. These batteries usually last 3-5 years, but they are susceptible to becoming depleted with time, particularly when the fob is frequently dropped. You could try replacing the battery with a new one but be sure it's the same size and voltage as the original. If you choose to use an alternative battery, it could cause the key to have an invalid key ID which will prevent it from paired with your vehicle.

The best method to replace the battery of a coin in a Nissan Qashqai Key Fob is to open it with the help of a small screwdriver with a flat head. Push in the screwdriver in tiny notch at the bottom of the fob and twist gently to separate the two parts of the key fob. Then, remove the old CR2025 button cell battery and insert an alternative one after taking note of its location on the fob.

Before you put the new battery into place be sure that there isn't any water damage or dirt on the terminals. If there is, wash the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are properly connected. They should be connected to the positive and negative poles of your battery.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water, it may be an indication of a chip problem inside the. The battery replacement won't fix this issue, and you'll have to purchase a new key fob. If the key fob has stopped working after dropping it, it's likely that the chip inside was damaged. You can usually get the key fob to work once again if it is removed and clean the chip using alcohol and paper towels and then put it back in.

One common error you may notice on your dashboard is "Key ID Not Correct." The vehicle is unable to recognize the key fob, and therefore will not allow the vehicle to start. This issue can be caused by various ways, including water damage, problems undetectable in the key fob's circuitry or RFID interference.

The key fob won't work if the 12 volt batteries are dead or fail to provide sufficient electric current. This could affect the Nissan Qashqai's keyless system, central locking and the ability to start the engine using the key fob. If you're unable to unlock or lock the door by hand, you should check the batteries in your key fob to make sure they're in good condition. You can also try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be able to be revived by a simple wash of clean water. You can also try cleaning the electronic chip using isopropyl Alcohol or an electronic cleaner. If none of these work it could be time to replace the entire key fob with an entirely new one.

If your Nissan Intelligent Key is still not functioning, there may be an issue with the connection between it and your car. To reconnect it, begin by turning the key into the ignition, without turning on the car. Continue to do this until the hazard light blinks twice. Turn off the vehicle and remove the key.

Open the fob compartment in your vehicle's fob compartment. It's usually located on a door's jamb or the handle of the driver's door. Find the button that says "program" and press it. When the process is complete you will hear an emitted sound.

It's time to put your Intelligent Key to the test. You must stand a certain distance away from the vehicle and press all the buttons on it. If the lights flash and the horn sounds this means that the key has successfully linked to the Nissan. You can also test it close to the Nissan.