UPVC Window Handle Replacement

It's simple to repair a broken window handle with the proper tools. It is essential to know the type of handle you have and the spindle's size before purchasing an alternative.

Older uPVC window handles have a spur which protrudes and locks on a wedge striker. These can be either right or left-handed and have to match when replacing.

What type of lock or handle do you have? I have?

There are many windows locks and handles made of upvc, Window Handle Replacement each with its particular advantages and uses. The type of handle you own will determine if your locking mechanism is efficient and if it's easy to open windows. As time passes, and with regular use the handles made of upvc on your windows could be damaged and worn out. This makes them less secure and less effective. In some instances they might even fall off completely. It is crucial to fix the handles on your window made of upvc when you begin to notice them falling off. This will stop possible burglaries and will keep your home safe.

It's a simple job that anyone can complete. You will need a few basic tools, but with appropriate knowledge, it's a straightforward process that should only take a couple of minutes. You must be aware of the type of handle or lock that you have on your window. This will allow you to choose the right replacement.

Inline Espagnolette Handles

They are typically located on the side of the window. They are flat in design and feature an opening that is connected to the locking mechanism on the frame of the window when it is turned. Inline upvc handles also have spindles that run through the middle of the handle and then into the frame of the window to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles are attached to the window frame by a single screw and are less secure than other varieties of window handle.

Handles that turn and tilt

The tilt and turn handles differ from other upvc handles because they can be turned for opening the window, and then tilted to the window to let air circulate. In general, they have a 7mm spindle on the back of the handle. They are available in both left and right handed versions.

When buying replacement upvc handles it is essential to verify the length of the spindle because not all handles are the same size. To determine the length of your handle made of upvc, simply drop something into the middle of the hole and measure how far it extends before it reaches an obstruction. This is the maximum spindle size that will fit in your windows.

What is a spindle?

uPVC window handles work similarly as doors, with the user turning the handle to operate an opening inside the frame. This opens the window so that it can be shut and opened. The handles could be damaged, particularly if they're used frequently or exposed to harsh environments. This can lead to the need to replace your uPVC windows handles as they may not be able to operate the window properly anymore.

There are many types of uPVC handle options, such as Espag, Window Handle Replacement Cockspur, and Spaded handles. They are designed to fit in the uPVC frames in a variety of ways. Each handle uses a specific spindle to secure the mechanism to the window. This is why it is essential to know the type of handle you have installed on your uPVC window so you can find the right replacement.

The base section of the handle will tell you what kind of upvc window handle replacement it is. There should be a "snap-in' cover over one screw that holds the handle base in the correct position. Take it off and you should be able see the second screw located at the opposite end of the base of the handle. After both screws are removed and you are able to remove the handle from the uPVC.

Once you have removed your uPVC window handle you need to carefully remove the spindle you have removed from the locking mechanism. Make note of the length of the spindle, as you'll need to make sure that you purchase a replacement that has the same length as the original handle and locking mechanism.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to corrosion, damage due to continuous use, or even the locking mechanism becoming looser. If this occurs, it is required to replace the window handle and the locking mechanism to restore the full functionality to your uPVC windows.

How do I take off the old handle?

Through time and regular use, window handles can be damaged or destroyed, and if this happens it is crucial to repair them as soon as you can to ensure the safety of your home. It is good to know that replacing a damaged or worn handle is a simple task that can be completed in less than one minute and doesn't require any specialist tools.

The first step in removing the old handle is to take off the screw situated at the top of the base of the handle. Once the screw has been removed, the handle will be pulled away. There will be another screw located at the bottom of the handle base, and this can be removed too. Once these two screws have been removed, the handle will be removed from the window's base.

After the handle has been removed, you can take the new handle and line up the fixing holes with the holes currently in the window frame. If there is a sticker or cap on the new handle, take it off it if needed and screw the handle in the appropriate position. Once the handle is set, it is important to test that it is working by turning the handle and making sure that the lock mechanism is activated.

Espag handles come with an extra spindle that is protruding from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows come with a blade with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that hooks over the frame's outer or transom bar cross-member within the window.

Once you have the new handle in place, you can insert the spindle into the lock inside the window and then tighten it down. Once the handle is firmly fixed, replace the'snap in' cover and the screw cap (if appropriate). Now that the handle is in use, open and close the window a couple of times to ensure it works correctly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The process is easy. You only need a screwdriver and a bit of patience. The first thing you need to do is make sure that the old handle is in the unlocked position and then take out any screws that are visible. you can replace them with screw caps if required. After removing the handle, you'll need to take note of the length of spindle that extends from the back. This is crucial since it will determine the kind of handle you'll need to purchase.

Espagnolette handles are the most popular type of handle for uPVC windows. They feature a spindle that runs through the handle and operates a locking mechanism within the frame of the window. Once the handle is turned it opens the latch on the window and allows it to open. Over time and through regular use, espagnolette handles can become damaged or impaired which is why it is essential to find replacements.

Cadenza handles are a type of uPVC handle that is typically used with tilt and turn windows. They feature a protruding blade that operates an interlocking mechanism that is multipoint within the window. They are more secure than the espagnolette handles since they only open from the inside. You can replace them with the same procedure as you would with espagnolette handles, but make sure the new handle is angled, not flat.

Once you have selected the correct handle, simply align the new handle with existing screw holes prior to screwing it into place. After that, you should put the screw covers back on and make sure the new handle functions correctly. This is accomplished by moving the handle from the locked position to the unlocked and vice versa a few times. It may be worth contacting an expert to see how you can fix any issues. They will often be able to guide you on the best solution to solve the issue in a fast and effective way.