Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to auto locksmiths with experience with the right equipment and technical know-how. They will be able to create and program new keys much faster than a dealership would and at a lower price.

If the key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. However, there are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead coin battery can hinder your peugeot 207 key replacement 208 from locking or unlocking and cannot start the engine. In this scenario you'll need employ the alternate method of starting that is described in the owner's manual.

Another reason why your 208 might not be starting is that the spark plugs have worn down. The spark plugs are responsible for sparking the fuel that starts the engine. However they have a finite life span. They'll eventually fail when they aren't used enough.

Fortunately, there's an easy solution to this issue. Check the voltage of the battery using a multimeter. If it is below 11.5 volts, then you need to replace it. If the battery has corroded it is essential to clean its contacts. This can be done by lifting the rubber covers that cover the two terminals of the battery and using wire brushes to clean any parts that are corroded from the battery. It is then time to reconnect the cables for the positive and negative poles.

Water Damage

If your 208 will not start and the battery hasn't been replaced, you must inspect the spark plugs. It could be that they are simply too filthy and don't spark. The spark plugs can be cleaned in the workshop.

Peugeot cars are equipped with a key with a transponder compatible with the immobiliser. This makes sure that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it won't send the proper signal to the vehicle.

Water damage is a common cause of this issue. This is a typical issue in warmer climates where the vehicle is exposed to rain or snow. In this case, you need to contact a reliable locksmith who will have the tools and equipment required to change the key's programming. They will also have the most up-to-date technology and equipment needed to create the Peugeot 208 smart key. The process should take no more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the old transponder chips using a new model that is based on electronic components that are mounted on a circuitboard. The new system is excellent when it's new, however the circuit boards begin to degrade with time and cease to function properly.

This can stop the immobiliser chip activating and causing your car to not start. If this happens, it's a good idea to get in touch with a Peugeot specialist or locksmith.

Another issue that is common is when the battery in the key fob gets depleted, which causes the key blade to stop being able to feed into the lock. A locksmith for cars will replace the battery and then cut a new blade for you. This is a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem in the event that your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer, which controls the central locking system of your Peugeot vehicle.

Rubber seals on the key fob stop water from reaching the electronic chip. The chip can be damaged by water when exposed to water for long periods of time. The high salt content of the pool or ocean water could cause damage to the key fob if it is submerged.

The module will need to be replaced if the peugeot car key replacement spare key isn't working anymore. This can only be done by a skilled auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to begin the engine. It is for this reason that you should only trust an authorized Peugeot locksmith to create and program a replacement.

Computer on board is not working properly

The computer on the board of your Peugeot is responsible for many of the systems within the car, from power windows to the airbags. If something goes wrong with these systems, it will usually show a code that identifies the issue. This code is saved in the system and stays there until the issue is resolved. This will often require the on-board computers to be replaced.

One of the most common reasons for the light flashing is loose or corroded connections within the airbag sensor. This can be caused by wear and tear, age or exposure to salt and moisture. It is essential to have this issue addressed as soon as you can, since an airbag that is not functioning properly could be dangerous in the event of an accident.

If your Peugeot is showing a card not detected error, then the key battery in the key fob might be dead or weak. This prevents the key fob from sending a signal that disarms your vehicle's standard immobilizer. Try this by pressing the unlock button on the fob's key, then trying to start your car. If this doesn't work then the battery on the key will need replacing.