How to Replace a kia ceed key fob Sportage Replacement Key

The key of a lot of Kia models has an electronic keyless entry system built into. This key is similar to the remote control and is exchangeable by a Kia dealer.

Key fobs might stop working due to a variety of reasons, including a dead battery, worn-out buttons signals, signal interference or water damage. Here are some helpful tips to assist you in getting your Kia sportage replacement key working once more.

How do you replace the remote key or smart key?

The battery in your Kia's intelligent key will eventually need to be replaced, whether it is a remote key that starts with a push button or a standard metal key that does not contain a transponder. This is especially in the event that your car displays a message telling that the remote or smart key is not powered by the battery.

It's a simple procedure. In order to replace the battery on the key fob remove the mechanical key from the slit in the back of the key fob. Next, pry open the cover. A small screw will be found inside the key fob to hold the battery in the correct position. Remove the old battery by removing the screw with the help of a small screwdriver. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're in good shape! You can now use the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) do not require programming. If you want to change the programming of your key, you'll need to write down the key code's number on the tag for the key code.

How do you replace the battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is not fully charged. A weak battery could cause other issues, like the check engine light flashing or the engine not working properly. Fortunately, replacing the battery on the key fob is a relatively simple DIY task that requires only a few basic tools.

Make sure that you shut off your vehicle and shut all doors prior to starting. Locate the small plastic piece on the bottom of your key fob, and move it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and align the new one in a way that the "+" positive side is facing you, and the "-" negative side is facing the fob's electrical contacts made of metal. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After installing the new battery after which you turn the key fob on and off in the ignition until the door locks up. Then you can test your Kia key fob to see if it is working properly again.

How do you replace a smart key

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade however, the standard key fob does not. Both key fobs are equipped with an internal battery that will eventually require replacing. This is a simple procedure that takes just two minutes.

Before you get started before you begin, ensure that you're on a level surface with adequate lighting and that your Kia is off. Also, keep in mind that there are tiny pieces inside the fob which could fall out if you are not careful.

The first step is to find the small release button on the backside of the fob. It will be a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened it is easy to take off the old battery and replace it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. Once you're done, your key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do you replace a mechanical key

The Kia keyfob is an excellent convenience that lets us lock or unlock our car by pressing one button. Like any device like a key fob, the Kia can have issues at times. Luckily, there are steps to take to fix these issues and ensure that our key fobs are in good condition in the long run.

One of the most frequent problems is a dead or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the case try replacing the battery with a fresh new one.

If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to wedge the plastic casing of the fob open. Be careful not to harm any internal components or scratch the plastic. Once the battery is removed and replaced with a brand new one.

Once the new battery is in, close and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that can fit into the slot). Test the key fob to make sure it is working correctly. Contact a dealer, or a locksmith to fix the issue in the event that the fob is not working. Make sure they cut you an emergency key that can work across all trunk and door cylinders to avoid lockouts again.