Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will reduce repair costs as well as increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great deal of damage to your home, making it very dangerous and potentially fatal. It is important to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and the new window will generally fit within the old frame very easily. If you have double glazed window repairs-paned windows which are held together by internal beading, it will be harder to remove and replace the old panes. In this case, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you plan attempt to remove the window panes by yourself it is crucial to wear the appropriate safety equipment such as gloves that are thick and eye protection. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards fall onto the fabric, not onto the floor, where they could be trampled.

It's a good idea to seal the gap after the glass is removed. This will prevent drafts and water from entering your property until a professional arrives to repair the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is large, you might think about a security door that has an integrated window, as this will offer the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows made of sash. In time, they could be affected by a variety of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. It's crucial to act immediately if you notice your uPVC windows are falling down.

Repositioning the hinges can help fix a window that is sliding. You'll first need to open the windows so you can get at the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Once you've repositioned the hinges, shut your window and verify the fit. If you are happy with the size of the window, tighten the screws to hold them in the right position.

If you can't reposition the hinges, you might require replacing the seal. Over time rubber seals can lose their elasticity and become dry, which causes them to lose tightness. It is important to replace your seal as soon as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles may also become loose. Most often it is due to screws that have become loose over time. However, it can also happen because the handle mechanism has worn out. It's relatively easy to fix a loose uPVC hand. First, you'll need to close the window and do a test fitting. The corners of the sash must be aligned with the casing joint. If it isn't then you can use a screwdriver to loosen the handle and then reverse the mechanism back into its original position.

3. Water Leaks

It is important to take action if get up each morning to discover mouldy walls and wet floors. The leaks of water from windows do can not only cause destruction of your home's structure but also undermine your efforts to control the temperature in your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame is either damaged or missing.

This is an easy fix that can be done by anyone who is a DIYer with the skills. Depending on how severe the issue is, old caulking might need to be removed. When it is time to uPVC repair, you must be careful not to over-caulk. This will only make your window more difficult to clean and reduce its energy efficiency.

Verify that the drainage holes are free of debris in them, and also that the sill pan has been properly angled to drain away from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed glass, it is more likely the issue is more with the seal rather than the frame. It is also possible to be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open in a breeze it could be hinges that are at the fault. They can be repaired by any skilled DIYer and can be done within a few minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that have hinges and, broken just like any mechanical component they will wear out over time. The process of replacing a hinge on a window is essentially a very simple process, but it's simpler with someone else to assist in holding the frame up.

It is also important to ensure that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrow on each hinge. This indicates the direction in which the window should be opened.

The issue can be caused due to opening the window in the wrong way or a faulty installation in the factory. It is usually possible to fix the issue by sending us a picture on our website. We will be pleased to offer you suggestions.

It is also important to grease the hinges regularly. Applying an engineering lubricant that is light to the hinges is a good method to accomplish this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. This is recommended to be done at least every year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different things. The hinges can also become disaligned as a result of wear, creating a gap where the sash meets frame. This can be easily repaired by giving them a thorough clean, however if they are beyond repair it could be necessary to have them re-aligned or replaced. The second is the interlock, which is located on the hinge side of the window, may also be misaligned, and again it's feasible to give them a clean but in some instances it could be necessary to have them replaced.

The next common reason for draughts are the window seals, these can become worn down or damaged over time, and let air escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures and lessen the risk of draughts.

The final method to cut down on the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler that can be put on top of your window sill. They can keep your home warm by blocking out cold air.

Your windows made of upvc will continue to provide excellent insulation and security in your home by performing regular maintenance and repairs. It is crucial to realize that all windows have a life span and eventually, they will reach the point when it's more efficient to replace them than repair them. If you are experiencing issues with your Upvc window you should consult an expert immediately.