Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. They do not get rotten or rusty like aluminum and timber.

It is crucial to wash and oil UPVC doors and windows regularly. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it can cause a huge amount of damage to your home, which can make it very dangerous and potentially fatal. You should take the time to make sure that your windows are in good working order.

Single-pane windows are fairly simple to replace and typically fit into old frames very easily. However, if windows with repairing double glazed windows panes are held in place by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this instance you'll need source some plastic spacers that assist the new pane to fit properly into the frame of the window.

If you are going to try to remove the window panes by yourself, it is essential to wear appropriate safety gear such as gloves that are thick and window repairs protective eyewear. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall onto the fabric and not onto the floor which could cause them to be trampled.

It's a great idea tape the gap once the glass has been removed. This will keep drafts and water from entering your home until a professional is able to fix the window. This will also act as a barrier, deterring any intruders from gaining entry to your home. If the gap is large, you may be interested in an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time, they may be afflicted by a variety of issues like sliding. A window that is sagging can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need to open the window so that you can get to the frame. Then, remove both the top and bottom hinges using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you've repositioned your hinges. If you're satisfied with the fit of your window, you can tighten screws to hold them in the right position.

If you aren't able to move the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity over time, Window repairs causing them to lose their tightness. It is essential to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

UPVC handles can also loosen. This is often caused by screws that have become undone over time, but it could also be due to the handle mechanism getting worn out. It's relatively simple to repair a loose uPVC handle. The first step is to close the window and then perform an initial test fit. The corners of the sash should be aligned with the casing joint. If it isn't then you can use a screwdriver or a wrench to loosen the handle and turn the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it's important to take action. Water leaks from windows can not only cause degrading of the structure of your home but also hamper your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

It is a fairly easy fix that can be completed by any DIY expert. Depending on how severe the issue is, old caulking may need to be removed. It is essential to keep in mind that when it is about uPVC window repairs, you should not be tempted to apply too much caulk and then make the area more difficult to clean and could reduce the efficiency of your energy.

Make sure that the drainage holes have no debris in them, and also ensure that the sill pan has been angled correctly to drain away from the window. In more serious instances, you might need to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. This is a fungus that thrives in damp conditions and can quickly spread throughout the house.

It is also important to remember that if the leakage originates from the glass in your double glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sagging. It is also possible to be repaired by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it blows open with the breeze. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Most households in the UK will have top-hung or side hung uPVC windows that have hinges and, just like any mechanical component they are susceptible to wear and tear over time. Changing a window hinge is essentially a very simple process but it can be easier when you have a person to assist in holding the frame in place.

Verify that the upvc window repairs hinges are open and closed in the proper direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The problem can be caused by opening the window improperly or due to a poor installation at the factory. Sending us a picture through our website can often solve the issue. We are happy to provide advice.

It is also important to grease the hinges on a regular basis. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window to open and close more easily. It can also reduce the chance of windows sticking and help prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent-based lubricants are not recommended as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. The hinges may also become unbalanced due to wear, causing gaps where the sash and frame meet. This can be easily fixed by giving them a good clean, but if they are beyond repair it may be necessary to get them re-aligned or replaced. The second is the interlock, which is located on the hinge of the window, can also become misaligned, again it may be possible to give them a thorough clean, however in certain cases, it may be necessary to have them replaced.

These seals can wear down or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping can help prevent draughts. Another alternative is to replace the window with glass that is low-emissivity, this will help to regulate indoor temperatures and will reduce the risk of draughts.

The last way to reduce draughts effectively is by using a draught-excluder. These are usually made of fabric tubes filled with a filler that can be placed over your window sill. They will help block out cold air and keep your home warm and cozy!

Your upvc windows can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. It is important to remember that all windows eventually wear out and it is more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your window made of upvc you should consult an expert as soon as you can.