How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have a distinct set of steps to add the second key. It requires dealer assistance using a handheld computer dubbed Tech-2. Then a new key and transponder are required to be purchased and programmed to the car.

Change your keys regularly to prevent one from deteriorating faster than another. This will keep your keys in top condition.

Replacement Case

Contrary to the classic Saab keys of old, the new keys have electronic components which makes it hard to create a duplicate. This has made stealing cars much more difficult than it was a few years ago. However, it has also made the replacement of lost keys a comparatively expensive endeavor.

Every owner of a 9-3 saab fob key replacement should have at minimum two working keys. It's expensive to replace a lost key as it requires replacing the CIM module, and programming the locking cylinders. Dealers charge between $100-$200 for this.

There are options to avoid these high costs. Some parts retailers will look up the code from a spare key (usually the same one that opens the doors and switches the ignition) and cut a new metal key blade at a fraction of the dealer's cost. The key must be exactly the identical to the original one for it to function in your vehicle.

You can also change the case yourself by following these steps. You will need a flathead screwdriver and some patience. Utilizing the screwdriver, slowly pry the plastic apart and remove the emergency key from the case. After the case is open, remove all electronics and put them back in the new case. Put the correct key and badge into the case.

Replacement Battery

The replacement battery for the saab Key fob repair 9-3 is an affordable part that can be replaced easily and quickly. The YouTube video of Cyclone Cyd demonstrates the procedure for replacing the remote fob battery with just four steps. This guide should work with any modern saab key fob though the process may vary slightly.

This button is usually located close to the Saab logo on the back of the fob. It's usually just below the Saab logo on the back of the fob. Then you will need a flathead screwdriver to insert into the small hole of this button. This should be sufficient to open the case so that you can replace the battery.

After the new battery CR1632 is installed You can then reassemble the remote key fob and then program it to your car. The entire process should not be more than an hour. It's a very easy procedure that doesn't require any special equipment.

The process can be a bit more complicated if you've lost the key, but it's possible. The dealer must find the VIN number of the car and then request a replacement key blade and TWICE module with the exact unique code. After that, they'll need to cut the replacement key and then program it using the latest software tool known as MDI.

Replacement Key Fob

The key fob is the part that locks and unlocks your car. It is equipped with a battery inside. Batteries are able to last for a short time and will eventually fail. This is a problem that happens with all cars and the good news is that you can replace the batteries in a majority of key fobs and not have to replace the whole case. You can buy replacement fobs on Amazon that come with all the electronic components already installed, so you'll be able to simply open the case and replace the old batteries. You'll need to take out the emergency key before you can replace the batteries. To accomplish this, simply insert an small screwdriver with a flat head into the slot that is in the middle of the. Work the screwdriver around the case, and it will split open, making it easier to remove.

If you're planning to replace your keys, keep an extra set on hand. This can save you a lot of money. If you have an additional key, request the dealer to cut it in half and program it to your vehicle. This is much less expensive than purchasing a new key fob.

If you don't have a spare car key, you can add an additional key to your car, but this requires a lot research and effort. The cost for adding a second key is several hundred dollars and saab key fob Repair it requires programming of the car's computer. This can be accomplished by a professional, however it's a costly option for most owners.

Replacement Ignition

The new SAAB 9-3 features an alarm system that is more sophisticated based on a key code. This means that when you lose your sole working key, acquiring an additional one could be extremely costly since the car needs to have a unique computer module fitted and must also be programmed to accept a new key. Even a dealer can charge hundreds of dollars to program an entirely new key, even if they're unable to do it.

If you've lost the only working key and a dealer is able to replace the computer in your car (known as the CIM or SAAB TWICE) to make a replacement, and will charge you a premium price for it. We can reprogram the existing EEPROM of your car's computer to make it ready to accept an additional key. This will save you more than 50% off the price you'd spend at the dealer.

If you've been a long time owner of a 03-11 saab key programmer 9-3, then you probably realize that the ignition key isn't the most durable. They can become incredibly sticky and the buttons are known to be removed from them every now and then which is why you should think about purchasing a new one if yours isn't functioning properly. It's not as difficult as it appears to replace the ignition key. With the right tools, it can be accomplished in a matter of minutes.