UPVC Window Repairs

Upvc windows are energy efficient and can help to reduce heating bills. However, as they get older, issues can develop that require repair. This can include faulty hinges, handles or locks.

DIY people can fix wooden windows with ease. It's cheaper than purchasing a new window.

Cracks

Cracks and breaks can be a major problem. If they are not repaired, they can cause water infiltration, less effective protection against cold weather, and even the possibility of structural damage. Find a local builder who specializes in the repair of uPVC frames. They must possess the necessary knowledge and experience, as well as the equipment needed to ensure the best results. This will ensure that your shattered window is repaired before it worsens and you don't have to replace your window glass or unit.

Small cracks in glass can be fixed by using a variety of home-based solutions. Superglue and masking tape are two of the most commonly used solutions to hold glass damaged in position for a short time. For more severe cracks, the tape might need to be extended on both sides.

Alternatively, two-part epoxy can be used to repair broken or cracked glass. It's available at a lot of hardware stores and is available for around $10. Make sure your workspace is prepared prior to mixing the epoxy. Also, ensure that you have all the equipment necessary for the job.

If you notice that your upper or lower sash has difficulty raising, it is likely because the cords that connect to the sashweights have been damaged. This is an easy fix that is done using a ladder and a flathead screwdriver. A drip cap that is rotten can be easily replaced at home. The drip caps that are not rot-free are available at a majority of home centers and can be nailed or caulked into place with ease. Lastly, if you have a double- or triple-paned window, be certain to ensure that one of the panes are not broken. The reason for this is that the gases that are trapped between the windows are responsible for increasing the energy efficiency of the window and should not escape.

Water Leaks

If your uPVC window is leaking, it can cause damage to your home and result in costly repairs. Water leaks may also cause structural damage to your home as well as the growth of mold. To minimize damage, it's crucial to address any issues caused by windows that leak immediately.

One common cause of window leaks is damaged sealant around the frame. Silicone caulking will restore the seal to its original condition and prevent leakage. It's also important to check for cracks and gaps around the frame as well as in the stone or brick walls surrounding your windows.

Another reason that can cause leaks in windows is a blocked drainage hole or a defective flashing. It's crucial to make sure the drainage holes are clean and free of obstruction, particularly during heavy rainstorms. It is also important to look at the window's flashing to ensure that it is well-sealed.

It's also crucial to check that your drip cap doesn't have any decay or is missing. A rotten or missing drip cap will let water in the window from above and cause damage to the structure of your home. Replacing the drip cap that is leaky is not a difficult task. It's as easy as purchasing the new one and nailing it in place.

A professional can also test your windows for watertightness. They can use a tool to measure the water-tightness of your windows and ensure that they meet the standards of the industry. If your windows fail the test, you will have to replace them. This is a costly repair however it's worth it for the comfort and safety of your family.

Sagging

If your windows don't shut properly, it could lead to various problems, such as drafts, uPVC repairs condensation, and an increase in energy costs. It could also mean that the windows were not installed correctly or the sealant has worn away. Fortunately, there are a few things you can do to fix the problem.

In order to repair your window properly, you need to set up a work space with plenty of natural light. Begin by laying out newspaper or an old blanket to shield the flooring from any splinters and drips that may fall from windows as you work.

It is also recommended to make use of a white cloth that has been immersed in a solution of detergent and water. This will prevent any stains of color from appearing on your windows. When you're ready to start working on your uPVC windows, start by marking where the hinge channel should be situated. Unscrew the channel and fill the screw holes inside the frame using epoxy (for uPVC frames) or wood filler. Be sure to smooth the hole before it sets.

After the holes have been filled, you can put in the hinge channel. Make sure it's aligned with the window jamb. Also, make sure that you drill the new screw holes about quarter inch away from the original locations.

Next, measure the length of the spindle protruding from underside of the handle. You can then order a replacement on the internet or bring your old one in to a hardware store for matching. Remove the setscrew off the operator shaft. File it flat to allow the set screw to secure onto the shaft. Now, your uPVC window should close without difficulty.

Broken Hinges

It will be difficult to open or closing your uPVC windows if the hinges are broken or aren't working properly. This could create a security problem and prevent your home from remaining warm or cool. It's simple to find a new window hinge for your uPVC windows. It's crucial to choose the right hinge for your windows.

The hinges have to be the same size to fit into the window frame. The most commonly used hinges for uPVC windows is standard 18mm or UPVC 15mm hinges for windows. There are also special hinges for wooden frames. The proper hinge will allow you to avoid common issues with your windows.

The hinges on your windows could be stiff or loose for a variety of reasons. The hinges may not be tightened enough. To check this, use an electric screwdriver to find the friction screw on the hinge's end. Loosen it. Then, you can adjust it by turning it either way.

If your UPVC window hinges are not working as they should, call Preston Glass Fix for a quick repair. Our technicians will examine the condition of your hinges for your windows and provide you with the best option for you. We can replace window hinges or retension them, or even install new lock mechanisms to ensure your UPVC Windows are secure and safe.

Locks that aren't working

UPVC window mechanisms and locks are a crucial part of home security. They make it difficult to open a window without breaking into the home. It can be a hassle when a lock fails but you don't need to replace the entire window.

Sometimes, the issue is a minor issue which could have been averted if you have had regular maintenance. This is the reason we recommend getting your uPVC windows checked regularly by our yearly maintenance package to help reduce the likelihood of having problems.

The majority of modern uPVC windows have espagnolette locks that work by pushing the nose of the handle across a wedge block then turning the handle to close the lock. They are effective at locking the window, but should they not be maintained in a timely manner, they could begin to fail. We recommend applying WD-40 to them a couple of times a year.

If you notice your uPVC window isn't opening and closing as smoothly as it did in the past, or when the lock isn't working properly, there may be a problem with the locking gearboxes within the frame. This is often difficult to access as it requires the removal of the seals around the frame of the window and then removing the handle.

A locksmith who specializes in UPVC repairs is able to identify the problem quickly and will then be able to repair the failed locking gearbox with a exact replacement. This is a fast and simple repair that can save you hundreds of pounds by cutting out the need to purchase new windows.