How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 sports a chic interior that is comparable to the Volkswagen UP and Citroen C1, as well as SEAT Ibiza. Its interior is of higher quality than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's key fob does a lot of work for you, including locking and unlocking your vehicle remotely. It also contains a mechanical key, which can be used in the event that the battery of the fob fails.

Dead Coin Battery

The key fob is an amazing invention that lets drivers lock and start their cars without the need to insert a physical key in the ignition. It does this through radio frequency signals that connect to the computer onboard of the vehicle.

The battery in the key fob is responsible for this signal and will eventually wear out and will require replacement. Depending on the model of your Hyundai, it may or not display a warning before the battery has died. Keep a spare keyfob in you to swap out the battery as quickly as it gets worn.

The key fob must be reprogrammed to the vehicle once the new battery is installed. This can be done using an OBDII or Hyundai Digital Key scanner, but it is usually easier to do in your Reno home. Follow the instructions in the owner's manual or look on YouTube for "how to replace and open a Hyundai keyfob battery." Make sure to take a picture of the old battery or note it down prior to removing it.

Once the key fob's been reprogrammed, it will begin working once more. If it isn't working then you'll need to go to an authorized dealer for a replacement or contact locksmith. They'll have the experience and tools to fix it.

Water Damage

A key fob is a handy piece of technology that lets you to lock your car from the comfort of your home, slide down the windows from outside and even start your vehicle. However, it's not a perfect solution and will eventually get worn out due to regular use. The procedure of replacing the Hyundai keyfob i10 battery is simple and cheap.

Dropping your key fob into the pool, a puddle or even the washing machine isn't atypical and is often saved, but only if you act quickly. Water is a very bad mix when it comes to electronics and a wet keys fob can lead to many issues, such as corrosion, short circuits and even complete failure.

In the beginning, you must try to get rid of as much water as you can. Flip the fob over and shake out any moisture that can be observed. You can also use a hairdryer or place it on a radiator to speed the drying process. After you've removed as much moisture as you can, consider placing the fob somewhere that is dry and warm where it will continue to dry for a few days.

Next, you should attempt to open up the fob and remove the battery. The majority of Hyundai I10 keys utilize the same battery type as many quartz watches, and are usually very easy to change. After replacing the battery, take a photo or note the position of the battery before closing the fob.

Contact with the battery is poor

The battery of your key fob may be depleted. This is a typical issue and typically the remote shows signs of trouble before it goes out completely. Make sure that the retainers are secured and do not have any corrosion on them. If they are, you can use a wirebrush and the cleaning solution for programming batteries to clean them. Make sure you use a button-cell that has the same size, voltage and specifications as the original.

It may also be an indicator that your alternator, which is the part that charges the battery while the engine is running, isn't functioning correctly. An inefficient alternator will drain the battery rapidly, causing the warning light to come on.

A quick voltage check can assist you in determining whether this is the case for your Hyundai. If the battery is operating, the problem could be with the circuit board or any other component of the key fob. You can access the key fob by pressing the small metal tab or button on either the front or back of the unit. After taking off the cover then insert a CR2032 and make sure to connect all the connections.

Reprogramming

Hyundai offers keyless entry on many of its models, making driving around Littleton, Parker, and Castle Rock, CO easier than ever. You can use a remote to start your car, open the doors, and lock them. It's not a guarantee of durability and a broken or damaged fob can cause problems. If your Hyundai key fob isn't working it could require reprogramming to work with your vehicle.

The first thing you must take care of is removing the battery. Typically, the button cell battery is contained within an aluminum tab. If you remove the tab and replace the battery, be sure to use the same size and voltage as your old battery.

After the battery has been replaced, close the tab and replace retaining clips. Test the key fob again to ensure that it functions.

If the key fob does not work, it may be time to talk to a locksmith or dealer. A locksmith or dealer can make a new key and remote for you, and can also program the key to work with your car. This service is usually paid for, but it's worthwhile if you want to keep your Hyundai key fob working. They can also help in locating the perfect Hyundai key fob that will meet your needs.