How to Replace a UPVC Window Handle

Don't be worried when your upvc handle has become broken. Replacing a window handle made from upvc is a relatively simple task and can be completed in a matter of a few steps.

If you have a cranked or inline espagnolette window handle, all of them come with a square spindle bar that protrudes from the back plate and is slotted into the locking mechanism.

Identify the type of lock and handle

Over time, window handles or locks may be damaged and lose their functionality. The good thing is that this issue can often be fixed without having to replace the entire uPVC window replacement companies unit. The first thing you should do is identify the size and type of your handle and lock. This will allow you to determine the replacement parts that you require.

You can identify the kind of handle by looking at the base. There is the screw or pin that is holding the handle to its base. If the screw is gone, it could indicate that the handle has split from the base section. If the handle has been split in the middle and is no longer gripping the spindle, this can be a sign that it is in need of replacement.

There are many uPVC handles, but the Espag handle is the most well-known. They are usually secured with two bolts and have spindles that are connected to the lock mechanism inside the window frame. These handles are used on uPVC tilt and turn windows.

Cockspur handles are another kind of uPVC handle. Similar to the Espag handle, however they have a lower projection from the frame. These handles are typically used on older uPVC window frames.

Finally, there are also Venetian window handles that are similar to the Espag handle but they have a flat base that allows them to be placed flush with the frame. These are a great choice for homeowners looking for an elegant, stylish handle that blends with their uPVC window frames. These handles come in a variety of colors that can be matched to any style.

Find the spindle's measurement.

It's important to be aware of how the handle is fixed in place before ordering the replacement. This will tell you how it is tight or loose and if it can fit correctly into the window frame. This can be determined by identifying the handle type and determining the spindle's measurement. The spindle is a metal shaft that connects the handle to the lock in the window frame. It's available in a variety of sizes with the current industry standard being 8mm. Older handles may have a 9mm cross-section, therefore it's important to measure the old one to ensure you get the correct size replacement.

There are many types of window handles. The most popular are the inline Espagnolette handles and Cockspur handles. These handles operate a locking system inside the window. They employ shootbolt rods that secure the window after it has been shut. They are held in place with pins or screws based on the type of handle you have.

You can buy replacement upvc handles on the internet or at most DIY stores. They are available in various finishes, and can be used to make new or replacement windows. They can also be key-locking or fire-escape non-locking for additional security.

To remove the old handle simply open the window towards the door and unscrew all screws that hold it in place. Be careful not to cause damage to the screws and place them in a container for future use. Once the screws are removed, remove them carefully from the handle. Measure the distance from the base of the spindle up to the tip. This will provide you with the information needed to buy the correct replacement. The spindle of the handle is the metal shaft that connects it to a lock gearbox in the window frame.

Take off the handle from the old one.

Changing the handle of a uPVC handle is a straightforward job that takes less than five minutes if you've got the appropriate tools. The first step is to identify the lock type and handle, which will help you find the correct replacement windows near me. After that, weighing the spindle will make sure that the new handle is a suitable for the job. The handle that was used previously needs to be removed and replaced with the new one.

Most uPVC handles are inline Espagnolette handles, which are equipped with central spindles that slot into the window's locking mechanism. They are typically easy to remove but could require force if they become stuck. The handle is usually secured by two screws that you can remove using a screwdriver. There may be a need to remove pins, based on the type of handle.

After you have removed the screws, you can take off the handle that was previously attached. The top of the base plate will be visible once the handle is in the open position, showing two screws can be removed. There's also an unimportant silver or color sticker that must be removed if in place.

With the screws that came off the handle, you can screw the new handle into the appropriate position. Align the screw holes on the window to the holes in the handle. After this is done then you can replace upvc window handle the caps on the screws and then test the new handle to make sure that it is working properly. The replacement of a uPVC window could be a quick and simple job, but it's important to ensure you do it correctly.

Fit the new handle

If you've managed to successfully take the handle off the frame, now is the time to put in the new handle. Start by locating and removing the screw covers using your screwdriver. Once removed, place them in a safe place and proceed to the next step.

Then, you can insert the new spindle into the handle by lining it up with the existing hole and screwing it into. Be sure to align the holes of the handle with holes in the window frame. You should use a screw identical to those used previously, or it could cause the handle to not being secure.

uPVC Espag handles come with a square 7mm spindle that turns the lock mechanism attached to the window. This handle style is used in the majority of modern uPVC windows. uPVC Cockspur (also called by the name Cotswold) handles feature an extended, curved nose that is secured to the outer frame or cross member of the transom bar. They are usually found on older uPVC Windows.

It's important to lock and unlock the window numerous times after the handle is installed. If everything goes according to plan, your replacement uPVC window handle should now be securely attached and operating smoothly. If not, the steps listed above will help you diagnose any issues and fix it quickly. Bridgewater Glass can help you when you're experiencing issues with your uPVC handles or any other home improvement that is glazed. Our glaziers are trained to repair or replace windows with a variety of frames and handles which makes us a great option for your double glazing requirements.

Test the new handle

Over time and through normal use, uPVC handles and locks can suffer from damage and wear and wear and tear. This can make them less secure and less effective which is why it's important to replace them right away. It's also a good idea to do this when you upgrade your windows, since changing your lock and handle will help maintain the integrity of your new windows.

There are a variety of uPVC window handles. Some are fixed by pins or screws while others have blades which slot into the lock mechanism. Each type has its own method of replacement, and it is important to know which kind you've got before you begin working on it.

Espag window handles are the most popular kind, and are typically found on the latest uPVC windows. They have a spindle that extends from the handle and goes into the lock gearbox, and when you open the window, it triggers the locking mechanism. They're also simple to remove however you should be careful not to harm the mechanism or the handle while doing so.

Cockspur handles are another alternative to uPVC window handles. They're fixed by a spur that is snagged onto the striker plate in the shape of a wedge on the frame, replace upvc window handle and when you close or tilt the window, it triggers the locking mechanism. This type of handle is more difficult to repair than other types however, it's still an excellent choice for the majority of homes.

Venetian handles are attached to the frame by two bolts and they have a low projection on the frame. This differs from the Espag handle. These handles are ideal for those who want to have a flush handle which blends into uPVC window frames. These are great for both residential and commercial properties.