Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like aluminum or timber.

It is essential to clean and oil UPVC windows and doors on a regular basis. This will reduce costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, making it very hazardous and possibly fatal. It is important to take the time to make sure that you're doing everything you can to keep your windows in good shape.

For single pane windows, it is fairly easy to replace them, and the new window is usually able to fit into the frame that was previously installed easily. If you have double glazed window repairs-paned windows that are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this case, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you are going to attempt to remove the window panes yourself it is important to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall onto the fabric and not on the floor and could be trampled under.

It's a great idea to tape the gap once the glass is removed. This will prevent water and drafts from entering your property until a professional comes out to repair the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap is particularly large, you might want to consider using an alarm door that comes with an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. However, over time, they may be afflicted by a variety of problems including sagging. A window that is sagging can cause problems with light, draughts or even security. It's important to take action when you notice your uPVC windows are falling down.

Repositioning the hinges could help fix a window that is sliding. You'll first need to open the windows so you can get at the frame. Then, you can remove the hinges on the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. After you've repositioned the hinges, close the window and verify the fitting. If you're satisfied with the fit of the window, you can tighten screws to secure them in the right position.

If you are unable to reposition the hinges, you could need to replace the seal. Over time, rubber seals lose their elasticity and dry out, which causes them to loosen. If this happens, it's crucial to replace the seal as quickly as possible to ensure your upvc window repair windows are waterproof and draught-proof.

uPVC handles may also become loose. This is typically caused by screws that have been removed over time, but it can also be caused by the handle mechanism wears out. It's a good thing that it's simple to fix a loose uPVC window repairs near me handle yourself. First, you'll need to shut the window and perform an experiment fitting. The corners of the sash should be aligned with the casing joint. If it doesn't then you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls every time it rains it's crucial to take action. Windows that leak water do can not only cause degradation of your home's structure but also undermine your efforts to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by damaged or Upvc Window Repair missing sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on the severity of the problem is, the old caulking might need to be removed. When it is time to uPVC repair, you must be careful not to over-caulk. This will make your window more difficult to clean and reduce its energy efficiency.

Make sure that the drainage holes do not have debris in them, and also that the sill pan is properly angled to drain away from the window. In more severe cases, you may need to replace the window.

Moldy sills and rotten ones are also signs of water leakage. The mold thrives in damp environments and is able to quickly spread throughout the house.

It is also important to note that if the leakage is coming from between the glass of your double-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or Upvc Window Repair sliding. Again this can easily be repaired by an uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open with ease, it may be hinges that are at fault. Anyone with the skills to fix them can replace these in a matter of minutes.

Like all mechanical parts hinges will wear out over time. Changing a window hinge is an easy process, but it's easier when you have a person to help hold the frame in place.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. Look for the arrows on each hinge to determine which direction the window should be opened.

The problem can be caused either by opening the window improperly or due to a poor installation at the factory. Sending us photos through our website can often solve the issue. We are more than happy to give assistance.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to operate and close more easily. It can also stop corrosion and decrease the chance of sticking. Ideally, you should do this once a year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges can also be unbalanced due to wear, which can cause an opening where the sash and frame meet. If they're beyond repair, it may be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge of the window, may also become misaligned, again it's feasible to give them a clean but in some instances it could be necessary to have them replaced.

The next most common reason for draughts are the window seals, these are prone to wear or damaged over time and let air escape through the gaps. Installing high-quality weatherstripping will help to stop draughts. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures, and reduce draughts.

The final method to cut down on the amount of draughts is to use a draught-excluder. These are typically fabric tubes filled with a filler that can be hung over your window sill. These will help to keep cold air out and keep your home warm and cosy!

With a bit of regular maintenance and repairs, your upvc windows will continue to provide an excellent level of security and insulation for your home. It is crucial to keep in mind that all windows eventually wear out and it may be cheaper to replace them rather than repair them. If you have any problems with your window made of upvc it is recommended to speak with an expert as soon as possible.