Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They don't rot or rust like timber and aluminum.

It is essential to clean and oil UPVC windows and doors on a regular basis. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, which can make it very dangerous and potentially fatal. It is important to take the time to ensure that you're doing everything you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace and will usually fit into the frames of the past easily. However when windows with double panes are anchored by internal beading, it will be more difficult to get rid of the existing panes and install new ones. In this situation you'll need to find some plastic spacers to help the new pane to fit correctly into the window frame.

If you are going to attempt to remove the glass panes yourself it is crucial to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes, so that any shards fall onto the fabric and not on the floor and could be trampled under.

After the glass has been removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent water and drafts from getting into the home until a professional comes out and fix the window. This will also act as a barrier that will prevent any intruders from getting access into your home. If the gap between the window and the door is significant, you may prefer a security screen that also has windows. This will provide the best of both.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. As time passes, they may be affected by a variety of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. It is crucial to act immediately if you discover that your uPVC windows are sliding.

To fix a window that is sagging you can try repositioning the hinges. To accomplish this, you'll need open the window to access the frame. Then, using the screwdriver, you'll be able to remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close your window and verify the fitting. If you're satisfied with the fit of the window, you can tighten screws to secure them in place.

If you are unable to reposition the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to lose tightness. It is essential to replace your seal as soon as you can in order to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. The majority of the time this is due to screws that have come loose over time. However, it can occur because the handle mechanism has worn out. It's relatively simple to fix a loose uPVC hand. You'll first need to close the window and do an experiment fitting. The corner joints of the sash should align with the casing joint. If it isn't you can use a screwdriver to loosen the handle. Then turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's crucial to take action. Windows that leak water do not only lead to the destruction of your home's structure but also hamper your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the issue the caulking used previously may need to be removed before a fresh layer can be put on. When it is time to uPVC repair, you should be careful not to over-caulk. This can make your window more difficult to clean and lower its energy efficiency.

It is crucial to make sure that the drainage holes are free of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more extreme situations, you may have to replace the window.

Mold spots and rotted sills are other signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double glazing repair-glazed glass it is more likely that the issue is more with the seal than the frame. It is also possible to be repaired by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with a breeze, it may be hinges at the fault. They can be repaired by any DIYer who is skilled and are usually completed in a matter of minutes.

Like all mechanical parts hinges will wear out over time. It's easy to replace a hinge on a window however it is easier if someone helps hold the frame.

Make sure that the uPVC hinges are closed and open in the correct direction. You can check this by checking for the arrows on each hinge, this indicates which way the window should be opened.

The problem can be caused either by opening the window improperly or a faulty installation in the factory. This issue can be fixed by sending us a photograph on our website. We will be more than happy to give you advice.

Regular lubrication of the hinges is essential. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regularly lubrication will help the window to operate and close more smoothly. It can also prevent corrosion and reduce the risk of sticking. The ideal time to do this at least once a year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. The hinges, also due to wear and tear may become displaced, which causes gaps to develop where the sash joins the frame. If they're beyond repair, it might be necessary to have them realigned. Secondly the interlock, this is located on the hinge of the window, can also be misaligned, and again it is possible to give them a good clean, but in some cases it might be necessary to get them replaced.

The second most frequent reason for draughts are the window seals. These can become worn down or damaged over time, and allow air to escape through these gaps. Installing high-quality weatherstripping will help to stop draughts. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help in regulating indoor temperatures and will lessen draughts.

Another method of reducing the amount of draughts is to use a draught-excluder. These are typically fabric tubes filled with a filler, which can be put on top of your window sill. These will keep your home warm by blocking out cold air.

With a bit of regular maintenance and repair windows made of upvc will provide excellent insulation and security for your home. It is essential to remember that all windows will eventually get worn out and it may be more cost-effective to simply replace them instead of fixing them. If you encounter any issues with your window made of upvc it is recommended to speak with an expert as soon as you can.