Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain, durable and long-lasting. They don't decay or rust as aluminum or timber.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great deal of damage to your home, which can make it very dangerous and potentially fatal. It is essential to make sure that your windows are in good working order.

Single-pane windows are fairly simple to replace and generally fit into frames that were previously in use very easily. However, if windows with double panes are held in place by internal beading, it will be more difficult to remove the old panes and put in new ones. In this situation, you will need to locate some plastic spacers that will help the new pane to fit properly into the window frame.

Wearing eye protection and thick gloves is a must if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards of glass fall onto the fabric, not onto the floor and could be trampled.

Once the glass is removed from the window, it's best to seal the gap with clear packaging tape or duct tape to prevent drafts and water from entering the home until a professional comes out and fix the window. It also acts as a barrier, deterring any intruders from gaining entry to your home. If the distance between the window and the door is large, you might need to consider security screens that includes windows. This will give you the best of both.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash window. Over time, they can be affected by a variety of issues, including sliding. A sagging window can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to stop the issue from becoming worse.

To fix a sagging window you can try to reposition the hinges. To do this, you'll have to open the window so that you can get to the frame. With an screwdriver, unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit of your window, tighten the screws to hold them in place.

If you are unable to reposition the hinges, you might have to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to lose tightness. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also loosen. This is typically caused by screws that have loosened over time, but it could also be due to the handle mechanism getting worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. First, you'll need to close the window and then perform a test fit. The corners of the sash should align with the casing joint. If it doesn't you can use a screwdriver to loosen up the handle. Then turn the mechanism into position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains it is important that you take action. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or missing.

This is an easy fix that can be done by anyone who is a DIYer with the skills. Based on the severity of the problem the caulking that was used up might need to be removed before a fresh layer can be applied. It is essential to keep in mind that when it is about uPVC window repairs, do not be tempted to 'over-caulk and then make the area harder to clean and can reduce your energy efficiency.

Check that any drainage holes are free of debris inside them and Window Repairs that the sill pan is angled correctly to drain away from the window. In more serious situations, you may need to think about replacing the window.

Other indicators of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double glazing near me-glazed glass, it is more likely the issue is related to the seal, not the frame. This can be easily repaired by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open in a breeze it could be hinges at the fault. They can be easily repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Like any mechanical component hinges are prone to be damaged over time. The process of replacing a hinge on a window is essentially a simple process but it can be easier with someone else to help you hold the frame in place.

It is also important to ensure that the uPVC hinges are opening and closed in the right direction. Look for the arrows on each hinge to determine which direction the window should be opened.

The issue can be caused either by opening the window incorrectly or by a poor installation in the factory. Sending us photos via our website will often resolve the problem. We are happy to provide suggestions.

It is also essential to grease the hinges on a regular basis. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication will make the window easier to open and close. It can also stop corrosion and decrease the chance of sticking. The ideal time to do this once a year. WD40 and other solvent-based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. Firstly the hinges, again because of wear and tear, can become misaligned, this will cause an opening to appear between the sash and the frame. If they're beyond repair, it may be required to realign them. Second, the interlock can also become disaligned. This is located on the hinge's side, and might require to be cleaned. In some instances it is possible to replace the hinges.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping can help keep draughts at bay. Another option is to replace the upvc window with glass that is low-emissivity, which will help regulate indoor temperatures, and also reduce the possibility of draughts.

Another, and most effective methods to reduce draughts is by using a draught excluder, these are usually fabric tubes filled with some type of filler. They can be positioned on top of your windowsill. They can help stop cold air from entering and keep your home warm and cosy!

With a little maintenance and repairs your windows made of upvc will provide a great level of insulation and security for your home. It is crucial to keep in mind that all windows will eventually wear out and it is more cost-effective to replace them instead of fixing them. So, if you're experiencing issues with your Upvc windows, it is recommended to seek assistance from a professional as soon as you can.