Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain and Upvc Window Repairs durable, as well as long-lasting. They don't rot or rust like timber and aluminum.

It is essential to clean and oil UPVC doors and windows regularly. This will reduce unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and even be fatal. It is important to make sure that your windows are in good condition.

Single-pane windows are fairly simple to replace and will usually fit into the frames of the past easily. However when you have double-pane windows that are anchored by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this case you'll need to locate some plastic spacers to assist the new pane to fit properly into the window repairs frame.

Wearing eye protection and heavy gloves is a must when you are planning to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes, so that any shards fall onto the fabric and not onto the floor, where they could be trampled under.

It's a great idea seal the gap after the glass has been removed. This will stop drafts and water from getting into your home until a professional comes out to fix the window repair. It also acts as a barrier to prevent any criminals from getting into your home. If the gap between the window and the door is significant, you may prefer security screens that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows made of sash. In time, they could develop a number of problems such as sliding. A window that is sagging can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's crucial to act fast to prevent the problem from worsening.

Repositioning the hinges could aid in fixing a window which is sliding. To do this, you'll have to open the window so that you can get to the frame. After that, using a screwdriver, you can unscrew the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after having moved your hinges. If you're satisfied with the fit of your window, you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you could need to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to lose their tightness. It is important to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles may also become loose. Most often, this is caused by screws that have come loose over time. However, it could occur because the handle mechanism has worn out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. You'll first need to close the window and do a test fitting. The joint at the corner of the sash must align with the joint on the casing. If it doesn't then you can use a screwdriver or a wrench to loosen the handle and then turn the mechanism back into position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it is important that you take action. The leaks of water from windows do not only lead to the degrading of the structure of your home but also hamper your efforts to control the temperature within your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be done by any DIYer who has the ability. Depending on the severity of the problem the old caulking may require removal before a new layer of caulk can be put on. It is essential to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk and then make the area harder to clean and can reduce your energy efficiency.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more severe cases, you may need to replace the window.

Mold spots and rotted sills are other signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

It is also important to remember that if the leakage is coming from between the glass of your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open in a breeze it could be the hinges that are at the fault. Anyone who is a skilled DIYer can fix these in a matter of minutes.

Most households in the UK will have top-hung or side hung uPVC windows that are hinged and like any mechanical part they are susceptible to wear and tear over time. It's very simple to change the hinges on a window however it is easier if someone helps you hold the frame.

It is also important to ensure that the uPVC hinges are opening and closed in the correct direction. You can do this by checking for the arrows on each hinge, this indicates which way the window should open.

Faulty window hinges could be the result of incorrectly opening the window a certain way or due to poor installation at the factory. Sending us photos via our website will often resolve the problem. We are happy to provide suggestions.

It is also crucial to ensure that the hinges are lubricated on a regular basis. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 or other solvent-based oils should not be used since they could damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different factors. The hinges, also due to wear and tear can become misaligned, this causes a gap to form where the sash meets the frame. If they are damaged beyond repair, it could be necessary to have them realigned. The second is the interlock, which is located on the hinge side of the window, can also be misaligned, and again it's possible to give them a thorough clean, however in certain cases, it may be necessary to get them replaced.

The seals may wear out or be damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the risk of draughts.

Another, and most effective ways to reduce the draughts in your home is to use a draught excluder. These are typically fabric tubes filled with some type of filler. They can be positioned on top of your windowsill. They can help block out cold air and keep your home warm and cosy!

With a bit of regular maintenance and repair your windows made of upvc will provide a great level of security and insulation for your home. It is essential to remember that all windows eventually wear out and it is cheaper to replace them instead of fixing them. So, if you're experiencing problems with your upvc windows, it is always recommended to seek assistance from a professional as soon as possible.