UPVC Window Handle Replacement

It's easy to repair a damaged window handle with the right tools. But it's essential to know your type of handle and the spindle's length prior buying a replacement.

Older uPVC window handles have a spur that protrudes and locks on the cockspur wedge striker. They can be left or right-handed and need to be matched when replacing.

What kind of lock and handle do I have?

There are a variety of window handles made from upvc and locks, each with its particular advantages and uses. The kind of handle you choose will determine the ease to open your windows and whether or not the locking mechanism works according to the plan. Over time and through regular usage, the window handles made of upvc are prone to wear or damage. out, rendering them less effective and secure. In some cases they might even fall off completely. It is important to repair your upvc window handles as soon as you begin to notice them falling off. This will help prevent potential break-ins and ensure your home is secure.

It's a simple job that virtually anyone can perform. You will need some basic tools, but with proper knowledge, it's simple and should take only a couple of minutes. To get started you'll need to determine the kind of handle and lock you have on your window and then identify the best double glazing replacement window.

Inline Espagnolette Handles

They are typically found on the side of the window. They have a flat design and Upvc window handle replacement feature an opening that is connected to the locking mechanism of the frame of the window when it is turned. Inline upvc handles have a spindle that runs through the middle of the handle into the window frame in order to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and feature distinct hook-shaped designs. Cockspur handles are fitted with a single screw that holds the handle to the frame of the window and are not as secure as other kinds of window handles.

Handles that tilt and turn

Unlike the other upvc handles the tilt and turn handles can be turned to open the window, and the handle can be tilted to the side for ventilation. Generally, they feature a 7mm spindle on the side of the handle. They are available in both left and right handed versions.

It is crucial to determine the size of the spindle when purchasing a new upvc handles. Not all are the exact same size. Drop something in the middle of the hole to measure the length. This is the largest spindle size that will fit into your windows.

What is the spindle?

uPVC window handles operate in a similar way as doors, UPVC Window Handle Replacement with the user turning the handle to activate a latch inside the frame. This opens the window so it can be opened and closed. But, at times, the handles may become damaged, especially when they are used frequently or exposed to harsh weather conditions. You may need to replace the handles on your uPVC window if they are not able to operate it correctly.

There are many different kinds of uPVC handles available including Espag, Cockspur and Spaded handles. These handles are designed in a variety ways to fit into uPVC frames. Each handle type utilizes a different spindle to lock the window mechanism. It is essential to determine the type of handle installed on your uPVC windows replacement to ensure that you replace it with the right one.

You can check what type of uPVC handle you have by looking at the base section of the handle. There should be a "snap in cover' over one screw which holds the handle base in place. After removing this you will be able to see the second screw that holds the base of the handle in position. After both screws have been removed, you should be able take the handle out of the uPVC.

After you have removed the uPVC window handle you need to carefully remove the old spindle from the locking mechanism. Make note of the length of the spindle as you'll need to ensure that you buy one that is the same length as the original handle and locking mechanism.

The main issue with most window handle problems with uPVC is that the spindle gets worn out and can no longer function properly with the locking mechanism. This could be due to damage caused by constant use or a loosening of the locking mechanism, or even corrosion that occurs over time. If this happens, it is required to replace the window handle and locking mechanism to restore full functionality to your uPVC windows.

How do I remove my old handle?

Window handles are susceptible to being damaged or broken over time. It is important to repair them as quickly as possible to ensure your security. It is simple to replace a damaged or worn handle. The task can be accomplished in less than a minute without the need for special tools.

To take off the handle, you must first remove the screw that is located at the bottom of the handle. Once the screw is removed, the handle can then be removed from the base section. There is a second screw that is located at the bottom of the handle's base and it is able to be removed as well. After these two screws are removed, the handle will be detached from the window's base.

After the handle has been removed, take the new handle and line up the fixing holes with the holes present in the window frame. If there is a sticker or cap on the new handle remove it if needed and put the handle back in the appropriate position. It is crucial to verify that the handle is working after it has been installed. Turn the handle and make sure that the lock mechanism is in place.

Espag handles come with spindles that protrude from the handle and slot into the multipoint locking mechanism that is on the window frame. Cadenza windows have a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hook over the frame that surrounds the window or the transom bar crossmember.

After you have installed the new handle, place the spindle into the window lock and tighten it. Once the handle is firmly fixed and secured, replace the snap-in cover and screw cap (if appropriate). Once the handle is ready for use, simply open and close the window a couple of times to make sure that it functions correctly and securely.

How do I install the new handle?

The process of changing your window handle made of uPVC isn't difficult and the process is actually very simple. You'll need a screwdriver and a little bit of patience. The first thing to do is to ensure that the handle you have previously used is in the unlocked position and then remove any screws that are visible, you can also replace these with screw caps if needed. After the handle has been removed and you are ready to take an note of the length of the spindle that protrudes from the back of the handle. This is crucial as it will determine what kind of handle to buy.

Espagnolette handles that are made of uPVC are the most well-known kind of handle. The spindle is inserted into the handle to operate the locking mechanism inside the frame of the window. The handle releases the latch and allows the window to open. In regular use and over time, handles made of espagnolette can become damaged.

Cadenza handles are a different kind of uPVC window handle that is commonly used on tilt and turn windows. They have a protruding blade that operates the multipoint locking mechanism inside the window. They are more secure than the espagnolette handles because they are able to open from the inside. They can be replaced using the same procedure as you would with espagnolette handles, but make sure the new handle is angled, not flat.

Once you have determined the right handle for you, you can simply line up the new handle to the existing screw holes and then screw it into place. Then, put the screws back on and make sure your new handle is operating correctly. You can perform this by dragging the handle between the locked position to the unlocked one for a few times. If you experience any issues, it may be beneficial to speak with a professional to see if they can assist you in solving the issue. They can often advise you on the best way to solve the issue in a speedy and effective way.