Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are easy to maintain, window repairs durable and long-lasting. As opposed to aluminium and timber they don't get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will save you from unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and may even be fatal. It is crucial to take the time to make sure that you are doing everything you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace and will usually fit into the frames of the past easily. If windows with double panes are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this situation it is essential to purchase plastic spacers in order to help the new pane fit into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor, where they could be trampled.

After the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional comes out and repair the window. It also acts as a barrier that will prevent any intruders from getting access into your home. If the gap is particularly large, you may want to consider using the security door with an integrated window, as this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber sash windows. However, over time they can suffer from a variety of issues, including sliding. A window that is sagging can cause problems with light, draughts, and even security. It's crucial to act immediately if you realize that your uPVC windows are sagging.

Repositioning the hinges can help fix a window that is sliding. To do this, you'll need open the window so that you can access the frame. You can then unscrew both the hinges at the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Close your window to test the fit after having moved your hinges. If you're happy with the fit, tighten the screws to ensure they remain in place.

If you aren't able to move the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and become dry which causes them to lose tightness. It is crucial to replace your seal as soon as you can to ensure that your upvc window repair window watertight and draughtproof.

UPVC handles can also become loose. This is often caused by screws that have become undone over time, but it can be caused by the handle mechanism wearing out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, you'll need to close the window and then perform an experiment fitting. The corners of the sash must be aligned with the casing joint. If it isn't then you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

It is essential to act if you wake up every morning to discover mouldy walls and wet floors. Leaks of water from windows can cause structural damage to your home and affect your ability to regulate the temperature inside your home. The most common cause for Window Repairs leaking uPVC windows is that the sealant around the frame has been damaged or missing.

This is a fairly simple fix that can be completed by any DIY expert. Depending on how severe the problem is, the old caulking may have to be removed. It is crucial to remember that when it comes to uPVC window repairs, you should avoid the temptation to "over-caulk in order to make the area harder to clean and decrease the efficiency of your energy usage.

Make sure that the drainage holes do not have debris in them, and also that the sill pan has been properly angled to drain away from the window. In more serious situations, you may have to replace the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass of your double-glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with a breeze it could be hinges that are at fault. Any competent DIYer can replace these in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that are hinged and like any mechanical part they will wear out over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is easier to do when you have a person to help hold the frame in place.

It is also important to ensure that the upvc window repair near me hinges are opened and closed in the right direction. You can check this by looking for the arrow on each hinge, this indicates the direction in which the window should be opened.

The issue could be caused either by opening the window improperly or by a poor installation in the factory. This issue can be fixed by sending us a photo on our website. We will be more than happy to give you suggestions.

It is also crucial to ensure that the hinges are lubricated on a regular basis. This can be accomplished by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It can also lower the chance of windows sticking and prevent corrosion. This is recommended to be done at least once a year. WD40 or other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also become disaligned as a result of wear, causing a gap where the sash and frame meet. They can be repaired by giving them thorough clean, however if they are beyond repair it might be necessary to have them aligned or replaced. In addition, the interlock could be misaligned. This happens on the hinge side and may need to be cleaned. In some instances it is possible to replace the hinges.

These seals are susceptible to wear and tear or be damaged over time, allowing air escape. Installing high-quality weatherstripping will help to prevent draughts. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures and lessen the possibility of draughts.

The final method to cut down on draughts effectively is by using a Draught-excluder. These are typically fabric tubes filled with a filler which can be hung over your window sill. They can help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. However, it is important to realize that all windows have a lifespan and they may reach an point at which it is more efficient to replace them than fix them. If you encounter any issues with your window made of upvc it is recommended to speak with a professional immediately.