How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an entry system that is keyless in. This key usually resembles an electronic remote and is able to be replaced with a fresh one from a Kia dealer or a locksmith.

Key fobs might stop working due to a variety of reasons, such as batteries that are dead, worn-out buttons signal interference or water damage. Here are some helpful tips to assist you in getting your Kia sportage replacement key to work once more.

How do you replace the remote key or smart key

No matter if your Kia is equipped with an intelligent key, remote key, push to start key or a regular non-transponder metal key the battery in these keys will eventually require replacement. This is especially true if your car shows a message that states the smart or remote keys are in poor condition.

This is a relatively easy procedure. To replace the battery of the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover open. A small screw is located inside the key fob, which holds the battery in the correct position. With a small screwdriver, remove the screw and pull out the old battery. Insert the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're in good shape If the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or when you need to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, it is necessary to note the key code number on the tag for the key code.

How to replace the battery

If the Kia key fob does not respond to pressing the lock/unlock button, it's likely that the battery is depleted. A battery that is not functioning properly can cause other issues, such as the check engine light appearing or the engine not running properly. Fortunately replacing the battery on the key fob is a fairly simple DIY project that requires only a few basic tools.

Before beginning the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Locate the small plastic piece at the bottom of your key fob, and jiggle it until a metal key slips out. You can then insert the key in the door handle of the driver to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a pry bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After you have installed the new battery then turn the key fob off and on in the ignition until the door locks up. Then, test your Kia key fob to determine whether it's functioning properly again.

How can you replace the smart key

You can have an ordinary keyfob or Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, while the standard key fob does not. Both key fobs contain an internal battery that will eventually require replacement. Luckily, this is an easy task that takes just two minutes.

Before you start it is important to make sure that you are on a flat surface with good lighting and that your Kia is turned off. Be aware that the fob is made up of tiny pieces that could be thrown off if you're not careful.

The small release button is located on the lower backside. It could be a circular button or rectangular slot. When you press it button, the mechanical blade will be released and you will be able to open the key fob.

After the key fob has been opened, remove the old battery. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. Once you're done it should be possible to lock, unlock and start your vehicle with your key fob, even if your engine isn't running!

How to replace a mechanical key

The Kia key fob is a great convenience that lets us lock and unlock our car at the click of an button. But like any device there are issues with it at times. Luckily, there are steps that can be taken to fix these issues and keep our key fobs in good working condition for the long term.

One of the most frequently encountered problems is a dead or dead battery. The fob could be able to stop working completely or even to stop working intermittently. If this is the case, try replacing the battery with a fresh new one.

If this does not solve the issue, you can use a flathead screwdriver standard to push the plastic casing of the fob open. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one.

Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia picanto key fob replacement has an emergency mechanical key that can fit in the slot). Test the key fob to check that it's functioning properly. If the fob still isn't functioning, contact an authorized locksmith or dealer to resolve the problem. To avoid lockouts in the future, ensure you have an emergency key that can work in all of the trunk and door cylinders.