UPVC Window Handle Replacement

It is easy to repair a broken window handle with the proper tools. It is essential to know the type of handle you have and its spindle size before you purchase a double glazing replacement window.

Older uPVC window handles have a spur that protrudes and locks on a cockspur wedge striker. These can be left- or right-handed, and must match when replaced.

What type of lock or handle do I have

There are a myriad of upvc window locks and handles, each with its own advantages and purposes. The type of handle you choose will determine if the locking mechanism you have is effective and if it is easy to open windows. Over time and through regular use, window handles made of upvc are prone to wear or damage. out, rendering them less secure and effective. In some cases, UPVC Window Handle Replacement they may even disappear completely. If you notice that your upvc window handles have been removed, it's crucial to fix them as soon as possible. This will stop possible burglaries and ensure that your home is safe.

The good news is that replacing your upvc window handles is a fairly simple job that can be done by nearly everyone. You will need a few tools, but with appropriate knowledge, it's an easy task that will take only a couple of minutes. It is important to be aware of the type of handle or lock that you have on your window. This will allow you to choose the right replacement.

Inline Espagnolette Handles

These are the most common kind of upvc handle and are typically located on the other side of your window. They are flat and come with an opening that engages the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the middle of the handle and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have distinct hook-shaped designs. Cockspur handles are attached to the frame of the window by a single screw and are less secure than other kinds of window handles.

Handles that can tilt and turn

The tilt and turn handles are different from other handles made of upvc in that they can be rotated to open the window and UPVC Window Handle Replacement then tilted into the window to allow air circulation. They have a 7mm spindle on the back and are available in left and right-handed versions.

It is essential to know the spindle's size prior to purchasing a replacement handles made of upvc. Not all of them are the exact same size. Drop something in the middle of the hole to test the length. This is the largest spindle size that will fit into your windows.

What is the spindle?

uPVC window handles work in a similar manner as doors. By turning the handle, you are able to open a latch in the frame. The window then opens and closed. The handles can become damaged, especially if often used or are exposed to harsh environments. It is possible to replace the handles on your uPVC window if they are not able to operate it correctly.

There are a variety of uPVC handles, including Espag, Cockspur, and Spaded handles. These handles are made in a variety of ways to fit into uPVC frames. Each handle type utilizes an individual spindle to lock the window mechanism. It is important to identify the type of handle installed on your uPVC windows to ensure that you replace it with a suitable one.

You can determine the type of uPVC handle you have by inspecting the base of the handle. There should be a "snap-in cover over one screw which holds the handle base in the correct position. Remove this and then you should be able see the second screw at the opposite end of the base section of the handle. After both screws are removed you should be able to pull the handle away from the uPVC window.

After you have removed the uPVC handle, carefully unscrew it from the locking mechanism. Note the length of the spindle. You'll need purchase a replacement with the same length as the original handle and locking device.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to corrosion, damage due to continuous use, or even a loosening locking mechanism. If this happens, you'll have to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the old handle?

Over time and through everyday use, window handles may become damaged or broken, and when this happens, it is important to repair them as quickly as possible to ensure the security of your home. It is good to know that replacing a worn or damaged handle is a relatively easy task that can be carried out in less than a minute and doesn't require any specialist tools.

The first step to remove the old handle is to take off the screw located on the top of the base of the handle. Once the screw is removed, the handle can be pulled away from the base section. There will be a second screw that is located at the bottom of the handle base, and it can be removed too. Once both of these screws are removed the handle can be completely detached from the base section of the window.

After removing the old handle, align the fixing holes of the new handle to the holes already present in the window frame. If there is a cap or sticker on the new handle, remove it if necessary and then screw the handle into the appropriate position. It is important to check whether the handle functions after it is installed. Turn the handle and ensure that the lock mechanism is in place.

Espag handles come with an extra spindle that is protruding from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism, while Cockspur handles have a long nose that hooks over either the frame's outer or transom bar cross-member within the window.

Once you have the new handle in place, slide the spindle inside the lock in the window and then tighten it down. Once the handle is securely fixed in place and secured, replace the snap-in cover and screw cap (if necessary). When the handle is ready to use, simply open and close the window a couple of times to make sure that it functions properly and securely.

How do I install the new handle?

It's not difficult to change the handle on your windows made of uPVC. The process is simple. All you need is a screwdriver and a bit of patience. The first thing to do is ensure that the handle you have previously used is not locked and then take out any screws that are visible, you can replace them with screw caps if required. After you have removed the handle, you will need to note the length of spindle that extends from the back. This is vital as it will determine what kind of handle to purchase.

Espagnolette handles that are made of uPVC are the most sought-after kind of handle. The spindle runs through the handle to activate the locking mechanism in the window frame. The handle opens the latch, allowing the window to open. During regular use and time, handles for espagnolette may be damaged.

Cadenza handles are a kind of uPVC handle that is usually employed with tilt and turn windows. They have an elongated blade that functions as an interlocking mechanism that is multipoint within the window. They are more secure than an espagnolette handles because they are able to open from the inside. You can replace them using the same method as you would with espagnolette handles however, ensure that the new handle is angled, not flat.

After you have chosen the correct handle, you can align the new handle with the existing screw holes before screwing it in place. Then, put the screw covers on and test the new handle. You can do this by moving the handle between the locked position to the unlocked a few time. If you encounter any issues, it could be beneficial to speak with a professional to see if they are able to assist in resolving the issue. They are often able to advise you on the best solution to resolve the issue in a speedy and efficient way.