How to Replace a Kia Sportage Replacement Key

The key in many kia ceed replacement key models comes with an entry system that is keyless into. The key can be compared to an electronic remote and can be changed with a new one from an Kia dealer or a locksmith.

Key fobs can stop working due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key working again.

How do you replace the remote key or smartkey?

No matter if your kia picanto key fob (ivimall.Com) is equipped with an intelligent key, remote key push-to-start keys, or a regular non-transponder steel key, the battery in these keys will eventually require replacing. This is particularly true if the vehicle displays a message that indicates that the remote or smart key has a low battery.

It's a fairly simple procedure. In order to replace the key fob battery, remove the mechanical key from the hole in the back of the key fob and pry open the cover. A small screw will be found inside the key fob that holds the battery in its place. Using a small screwdriver, take the screw off and remove the battery that was in place. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock and unlock buttons. It's good If the doors lock and unlock as expected. You can now use your Kia's hands-free lock/unlock feature when your fingers start to get cold or you need to go on errands around Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're required to reprogramme your key, you'll have to note the key code number on the key code tag.

How do you replace a dead battery?

If the kia picanto spare key key fob doesn't respond to pressing the lock/unlock button, it is most likely that the battery is depleted. A low battery may also cause other issues such as the check engine light turning on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires only the most basic tools.

Before starting the process ensure that your vehicle is off and all doors are shut. Find the small metal or a plastic piece near the bottom of the key fob. Move it until the key pops out. You can then insert the key into the handle on the door of your driver to open your car.

To replace the key fob battery, remove the rear cover and use a pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then orient the new one in a way that the "+" positive side faces you, while the "negative" negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After installing the new battery after which you turn the key fob off and on in the ignition until the door locks up. You can then test your Kia's key fob once more to ensure it's working as intended.

How do you replace the smart key

You can have an ordinary keyfob or Smart Key depending on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs have a battery that will eventually require changing. Fortunately, it's an easy process that only takes about two minutes.

Before you begin before you begin, ensure that you are on a level surface with adequate lighting and that your Kia is off. Keep in mind that the fob has tiny pieces that could fall if you're not careful.

The release button for the small size is located on the lower backside. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open it is easy to take off the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. Once you're done, your key fob should be able to lock and unlock your vehicle even if it's not running.

How do I replace a mechanical key

The Kia key fob is a wonderful convenience that lets us lock and unlock our car at the press of a button. But like any device there are issues with it at times. Luckily, there are ways to resolve these issues and keep our key fobs in good working order in the long run.

One of the most frequent problems is a dead or dead battery. This could cause your device to stop working or work intermittently. If this is the problem, replace the battery with an entirely new battery.

If this doesn't fix the problem then try using a normal flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to damage internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure that it's working properly. If the device not working, contact an expert locksmith or dealer to resolve the issue. To avoid lockouts in the future, make sure you get an emergency key that will be able to work with all trunk and door cylinders.