Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain, durable and long-lasting. They do not rot or rust like timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will save you from unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it could cause a large deal of damage to your home, Window Repairs making it very hazardous and possibly fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows it can be relatively simple to replace them, and the replacement will generally fit within the frame that was previously installed easily. However If you have double pane windows that are held in place by internal beading it will be more difficult to remove the panes that are in place and replace them with new ones. In this situation it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass yourself. It is also a good idea to lay down a drop cloth prior to when you begin working on the glass, so that any shards will fall onto the fabric instead of landing on the floor where they could be trodden under and cause further damage.

After the glass has been removed and the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to stop drafts and water from entering the home until a professional comes out and fix the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap is large, you may be interested in an alarm door that comes with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash window. Over time, they can develop a variety of issues that include sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from worsening.

To fix a sagging window you can try repositioning the hinges. To accomplish this, you'll have to open the window to get to the frame. With an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have relocated your hinges. If you're happy with the fit, tighten the screws to ensure they remain in position.

If you are unable to reposition the hinges, you might have to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loose their elasticity. It is essential to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

uPVC handles could also become loose. This is typically caused by screws that have been removed over time, but it can also be caused by the handle mechanism wears out. It's relatively easy to fix a loose uPVC hand. First, you'll need to close your window and do an initial test fit. The corners of the sash need to be aligned with the casing joint. If it isn't then you can use a screwdriver or a wrench to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

It is essential to act if you awake each day to find a smoky wall and floors that are wet. Water leaks from windows not only lead to the destruction of your home's structure but also undermine your efforts to control the temperature inside your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

It is a fairly easy fix and should be undertaken by any skilled DIYer. Depending on the severity of the problem the caulking used previously may need to be removed before a fresh layer can be applied. It is essential to remember that when it is about upvc window repairs near me window repairs, do avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and reduce your energy efficiency.

Verify that the drainage holes have no debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you might have to consider replacing the window.

Mold spots and rotted sills are another sign of water leakage. This is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double-glazed window repair, it is more likely that the issue is with the seal than the frame. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or if it opens in a breeze. They can be easily repaired by any skilled DIYer and can usually be done within a few minutes.

Like any mechanical part hinges are prone to wear out over time. The process of replacing a hinge on a window is essentially a very simple process, but it's easier when you have a person to assist in holding the frame up.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrow on each hinge, this indicates the direction in which the window should open.

The issue can be caused by opening the window incorrectly or due to a poor installation at the factory. Sending us photos through our website can often solve the issue. We are always happy to provide advice.

It is also essential to lubricate the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is a good way to do this. We suggest using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more easily. It can also stop corrosion and reduce the risk of sticking. This must be done at a minimum every year. WD40 and other solvent-based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different things. The hinges can also become unbalanced due to wear, which can cause an opening where the sash meets frame. They can be fixed by giving them a thorough clean, however in the event that they are beyond repair it may be necessary to get them aligned or replaced. The interlock, which is located on the hinge of the window, may also become misaligned, again it is possible to just give them a clean but in some cases it might be necessary to have these replaced.

The next most common reason for draughts are the window seals. These can become worn down or damaged over time and let air escape through these gaps. Replacement of these with high-quality weatherstripping can help stop draughts. Another alternative is to replace the window with low-emissivity glass, this will help to regulate indoor temperatures and again will lessen draughts.

The last way to reduce draughts effectively is by using a Draught-exclusion device. These are usually made of fabric tubes filled with a filler that can be hung over your window sill. They will help stop cold air from entering and keep your home warm and cosy!

Your windows made of upvc will continue to provide excellent insulation and security in your home with a little regular maintenance and repairs. It is crucial to keep in mind that all windows eventually become worn out, and it may be more cost-effective to replace them than to repair them. If you are having issues with your upvc windows, it's recommended to seek help from a professional as soon as you can.