Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they do not rust or rot.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will help prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home, and could even be fatal. It is crucial to take the time to make sure that you're doing all you can to keep your windows in good shape.

For single pane windows, it can be relatively simple to replace windows, and the new one is usually able to fit into the frame of the previous one easily. However, if you have double pane windows that are secured by internal beading it will be more difficult to remove the existing panes and install new ones. In this instance it is essential to buy plastic spacers to aid in fitting the new pane into the window Doctor near Me frame.

Wearing protective eyewear and thick gloves is essential for anyone who plans to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall on the fabric and not onto the floor, where they could be trampled.

Once the glass has been removed, it's a good idea to cover the gap with clear packaging tape or duct tape to stop drafts and water from entering the property until a professional comes out and repair the window. This will also act as a barrier that will prevent any intruders from gaining entry into your home. If the gap between the door and the window is large, you might want to use an alarm system that has a window. This will give you the best of both.

2. Sagging

Upvc windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they are susceptible to a range of problems including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from worsening.

Repositioning the hinges could aid in fixing a window which is sliding. To accomplish this, you'll have to open the window to get to the frame. With the screwdriver, you'll be able to remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have moved your hinges. If you're happy with the fit, tighten the screws until they stay in the right place.

If you can't reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause their tightness to decrease. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles could also loosen. The majority of the time it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, uPVC repair you'll need to close the window and then perform an initial test to ensure that it fits. The joints at the corners of the sash must align with the joint on the casing. If it does not you can use a screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant around the frame has been damaged or not present.

This is a simple fix that can be done by any DIYer who is competent. Depending on the severity of the issue the old caulking may need to be removed before a new layer is applied. When it is time to uPVC repair, you must avoid 'over-caulking'. This will make your window more difficult to clean and decrease its energy efficiency.

Verify that the drainage holes are free of debris inside them and ensure that the sill pan is angled correctly to drain away from the window. In more serious cases you might need to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the house.

If the leakage occurs between the double-glazed glass it is more likely that the problem is with the seal than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open with ease, it may be hinges at the fault. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Nearly every home in the UK will have either top hung or side hung uPVC windows that use hinges and like any mechanical part they are susceptible to wear and tear over time. The process of replacing a hinge on a window is essentially a simple process, but it's easier to do when you have a person to help hold the frame in place.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. Check for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a particular manner or because of inadequate installation at the factory. Sending us a photo via our website will often resolve the problem. We are always happy to give advice.

Regular lubrication of hinges is also essential. Applying a light engineering lubricant on the hinges is an ideal way to do this. We suggest using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window to operate and close more easily. It also decreases the risk of a window sticking and prevent corrosion. Ideally, you should do this at least once a year. WD40 and other solvent based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by different factors. Firstly the hinges, again because of wear and tear, can become misaligned, this can cause gaps to develop where the sash joins the frame. They can be repaired by giving them a good clean, but when they're beyond repair, it may be necessary to get them realigned or replaced. The interlock, which is located on the hinge of the window and can also be misaligned, and again it is possible to just give them a thorough clean, however in some instances it could be necessary to have these replaced.

These seals can wear down or become damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the risk of draughts.

Another, and most effective methods to reduce draughts is by using an draught excluder. These are typically made of fabric filled with some type of filler. They can be put on the top of your windowsill. They will keep your home warm by blocking cold air.

Your windows made of upvc will continue to provide excellent insulation and security for your home with regular maintenance and repairs. It is important to remember that all windows eventually get worn out and it may be more cost-effective to simply replace them than to repair them. If you encounter any issues with your Upvc window you should consult a professional as soon as you can.