Double Glazing Door Lock Repairs

Is your uPVC window or door mechanism not working properly? Perhaps the door or window handles aren't aligned properly or are difficult to use.

You'll lose energy if your double-glazed doors don't perform as they should. This increases the risk of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.

Snapped Key

It can be frustrating when a key snaps inside a lock. It also poses a security risk since the door might not lock and could leave you vulnerable to intruders. There are a few easy solutions you can use to resolve the issue and get your door working again.

Remember to remain calm. If you panic you could end up pushing the damaged key further into the lock.

Next spray WD-40 or a different penetrating oil into the lock to aid in making the broken piece slide out more easily. You can also use the screwdriver to break any pieces stuck. If you have a part of the key that is stuck out and is not being removed, grab it with a paperclip or other thin metal object and pull it. Both methods work, but be careful not to push the damaged piece of the key even further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades also work well for this. If you don't have any of them handy, you can use needle-nose pliers to bend and create hooks. Finally, you can make use of a pair of tweezers to grab and remove the remaining pieces of broken keys.

If you are unable to get the broken piece of key out, try using a lock de-icer. This is usually available at all hardware stores. It works by freezing any moisture or ice that might be inside the lock.

If none of these solutions seem to work, it could be time to contact a locksmith. Fitlocks experts can quickly fix issues such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also modify your double glazing door mechanisms to make them more user-friendly. You can request repairs to your double-glazing online or call us to discuss your requirements.

Broken Cylinder

A damaged cylinder could pose a serious security risk. Luckily, it's an easy repair for professional locksmiths to complete. A locksmith must tap the cylinder to fix it. This can be done with a hammer or other tool. However, the best method is to use a wire or a long match. The match or wire's end in the keyway. The locksmith can strike the lock and break it open. This is much safer than using a hammer, which could damage the lock.

The most frequent cause for cracks in the head of a cylinder is due to overheating. This can occur when the block and Repair My Windows And Doors the cylinder head are made from different metals like cast-iron and aluminum. Different metals will heat up and cool off at different rates. This could cause localized hotspots to expand faster than the rest.

Corrosion can be a reason for cracks in the cylinder. If the head and block of the cylinder are not maintained correctly they may be corroded or rust, which can cause them to expand faster than they would normally. As time passes, this may also cause cracks.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn, it could be due to a variety of reasons. This issue could be caused by a faulty locking mechanism, or misalignment or a worn-out handle.

Fortunately, this is an easy and inexpensive fix for most homeowners of double glazing. A professional locksmith is able to solve the issue within one hour of arriving at your home. They can replace the locking mechanisms, or change the window handles and replace the gearboxes based on your specific needs. A professional locksmith will be able to advise you on the most cost-effective solutions for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders that offer an additional layer of protection from burglars. It's a small price to pay for the peace-of-mind that comes from knowing your uPVC door is secured.

Broken Handle

It's not surprising that window handle locks may break. They have intricate mechanisms which deteriorate over time. It isn't always easy to pinpoint the reason behind a broken window handle lock and fix it correctly.

Fixing the broken handle, whether it's an internal latch or locking mechanism will increase the security of your uPVC door and prevent draughts. It can be expensive to repair or replace the handle in a way that isn't done correctly. It can also harm the frame and the lock of your door.

Screwdriver When the window is open and the screw loose, loosen the handle. The screw should be on the inside of the back plate, and is normally concealed by an attractive cover for the screw for aesthetic reasons. Be sure not to lose any of the internal parts within the handle, such as the levers or plates on either side of the spindle. Keep them in the same order to make it simpler to replace them in the event of a need.

Next, turn the handle to make it 90 degrees towards the window frame. Then, loosen the screw at the back of the handle that holds it to the internal spindle with another screwdriver. Once the screw is released, you'll be in a position to pull the handle away and pull off the damaged spindle. Replace this with a new one, making sure it's the same length as the previous one (you can typically find these online or in hardware stores) and then securely screw it in place. Do not tighten the screw too much as this can cause damage to the handle and window frame.

Check that the new handle is correctly fitted, then close and test the handle. It should function smoothly and you'll be able to open your window once more.

While you're working on the handle, don't forget to check your uPVC windows are shut properly. If they aren't closing properly, you may experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they are able to shut properly.

Broken Spindle

It is quite common that the spindle in the handle breaks, rather than the handle itself. This is most frequent in upvc window repairs tilt and turn windows. These kinds of windows require a handle which operates a locking mechanism in the window frame. The handle is attached to a central rod which in turn activates mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism is not able to open after the handle is turned, it is most likely the spindle is damaged. This can be a frustrating problem.

There are ways to fix this problem. A skilled locksmith can quickly and efficiently fix this problem. They will be able to take apart the window handle using a tool to remove the wheel component of the mechanism where the spindle is. This can be done without damaging the handle or causing any other damage to the window frame.

Once the wheel is removed, the technician can examine the spindle to determine what has caused it to break. This involves breaking down the spindle into its individual parts and carefully recording their general condition, as in addition to any specific areas of wear or damage. This process is usually performed by technicians in an environment that is clean.

The next step is to clean the damaged spindle, this assists in removing any debris or dirt that might be obstructing its normal operation. After that the spindle is cleaned, it can be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is the same size to the original. The technician will then drill matching holes into both pieces. This ensures that the new spindle is an exact fit with the handle.

If the damaged spindle is beyond Repair My Windows And Doors, it could be necessary to replace it completely. Home centres sell generic replacements, but if the style of your window is rare then it will be necessary to speak with a woodworker or cabinet maker who can replicate the exact component for you. After the spindle is installed, it is attached to the handle. Place the screw holes on the handle with the existing screws in the frame. Once the handle is seated, you can operate your uPVC windows.