UPVC Window Repairs

Upvc windows are able to reduce heating costs and are energy efficient. However, as they get older, problems may arise that require repair. This can include faulty handles, hinges, or locks.

Wooden window repair can be relatively straightforward for DIY enthusiasts to tackle themselves. It can also be cheaper than a new replacement window.

Cracks

Cracks and tears in windows made of uPVC can be a serious issue. Windows that are not repaired can lead to water intrusion and weaker barriers to cold weather, and even structural damage. It is important to find a local repair or builder that specialises in repairing uPVC frames and can demonstrate the skills, experience and tools needed to produce the most effective results. This will ensure that your shattered Window Doctor is repaired before it worsens and you don't need to replace your window glass or unit.

Small cracks in glass can be fixed by using a variety of home-based solutions. Masking tape and super glue are among the most popular products that can keep cracked glass in place for a while. For more severe cracks, the tape may need be extended on both sides.

You can also make use of two-part epoxy to fix damaged or cracked glasses. Most hardware stores sell this product for around $10. Ensure that your workspace is prepared prior to mixing the epoxy. Also, make sure you have the correct tool for the job, for example, a soldering tool.

If you find that your lower or upper sash has difficulty raising it could be because the cords connected to the sashweights have been damaged. Fortunately, this is an easy fix that can be made using the ladder and a flathead screwdriver. Replacing a damaged drip cap is another simple repair that can be done at home. Drain caps that are free of rot are available at most home centers and can be secured with nails and caulked into place with ease. Check that the glass of a triple- or double-paned window isn't cracked. The reason is that the gases in the space between the windows are responsible for increasing the efficiency of the window and must not escape.

Water Leaks

If your uPVC window is leaking, this can ruin your interior and result in costly repairs. Water leaks can also cause structural damage to your home, as well as mold growth. To avoid damage, it's important to address any issues caused by leaky windows as soon as you can.

A damaged sealant around window frames is a common reason for leaks. Silicone caulking can restore the seal to its original state and stop leakage. It is also essential to look for cracks and gaps in the frame as well in the stone or brick walls that surround your windows.

Another common reason for leaking windows is blocked drainage holes or a defective flashing. It is important to ensure that the drainage holes are clean and free of obstruction, particularly during heavy rainstorms. It is also important to examine the window's flashing to ensure that it's well-sealed.

It is also important to make sure that your drip cap isn't broken or damaged. A rotted or upvc window repairs damaged drip cap can allow water to enter the window from above and cause damage to your home's structure. Replacing the drip cap isn't difficult and generally a simple process of buying a new one and putting it in the right spot.

It's also a good idea to have your windows checked for water-tightness by a qualified. They can use a special tool to measure the water-tightness of your windows to make sure they are in line with industry standards. If your windows don't pass the test, you'll need to replace them. This is a costly fix, but it's worth it for the security and safety of your family.

Sagging

If your windows do not close properly, it can lead to a number issues including drafts, condensation and a rise in your energy bills. It could also be an indication that the windows weren't properly installed or the sealant is worn out. There are several things you can do to resolve the issue.

The first step is to prepare your workspace in a space that has plenty of light to help repair your window correctly. Start by laying down newspapers or an old blanket to shield your flooring from any splinters or drips from the windows while you work.

Use a white cloth soaked in a mixture of water and detergent. This will ensure you don't leave any color stains on your windows. When you're ready to work on your uPVC windows, start by making note of where the hinge channel must be situated. Unscrew the channel and fill the screw holes inside the frame using epoxy (for uPVC frames) or wood filler. Be sure to scrape the hole you have filled before it sets.

Install the hinge channel once the holes have been filled. Make sure you center it on the window jamb and then drill the new screw holes approximately a quarter-inch from the original locations.

Then, measure the spindle protruding from the underside of your handle. You can order an alternative or bring it to a shop selling hardware for matching. Remove the setscrew off the operator shaft. Flatten it to allow the set screw to be locked onto the shaft. Now your uPVC window should be closing easily.

Broken Hinges

If your uPVC window doctor near me hinges are damaged or aren't functioning properly and you are unable to open or close the window, it will be difficult to open or upvc window repairs close the window. This can be a security issue and also prevent your home from being warm or cold. You can easily get a new hinge for your uPVC window. It is essential to select the right hinge for your windows.

The hinges must be the same size in order to fit inside the frame of the window. The most popular hinge for uPVC windows is standard 18mm or UPVC 15mm window hinges. However, there are specialised kinds of window hinges that are suitable for other types of frames such as wooden frames. Getting the correct type of window hinge for your windows can assist you in avoiding the typical issues that homeowners have with their windows, such as not closing properly.

Your window hinges could be slack or stiff for several reasons. The hinges may not be properly tightened. To check this, use an electric screwdriver to locate the friction screw on the hinge's end. Loosen it. You can then adjust it by turning it either way.

Contact Preston Glass Fix if your UPVC window's hinges don't work properly. We can offer a quick fix. Our technicians will examine the condition of your window hinges and provide you with the best solution for your needs. We can replace the window hinges, re-tension them or install new locking mechanisms to ensure that your UPVC windows are safe and secure for the long haul.

Faulty locks

UPVC window locks and mechanisms are a very important part of the security of your home, they make it extremely difficult to open the window without breaking in. It can be a hassle when a lock fails however, you don't have to replace the entire window.

Often the problem can be a minor issue that could have been avoided if you have had regular maintenance. This is the reason we recommend that you have your uPVC windows maintained regularly using our yearly maintenance package to minimize the risk of issues.

Modern uPVC windows come with espagnolette locks. These work by pushing the nose of the handle over a wedge block, and then turning it to close the lock. They are effective in locking the window, but when they are not maintained properly, over time they can begin to fail. We recommend applying WD-40 to them a few times per year.

If you're noticing that your uPVC window isn't opening and closing as easily as it used to, or when the lock isn't working correctly, it could be a problem with locking gearboxes in the frame. This can be difficult to access because it requires the removal of the seals around the frame of the window and then taking off the handle.

A locksmith who specializes in UPVC repairs will have the expertise to diagnose this fault quickly and will then be able to repair the failed locking gearbox with an exact replacement. This quick and simple fix can save you hundreds of dollars by not the need to purchase new windows.