Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They don't decay or rust as aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will save you from costly repairs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and even be fatal. It is crucial to take the time to ensure that you are doing everything you can to ensure that your windows are in good repair.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. However when windows with double panes are held in place by internal beading it will be more difficult to remove the existing panes and install new ones. In this case it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not onto the floor, where they could be trampled.

Once the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to prevent water and drafts from entering the home until a professional is able to come out and repair the window. It also acts as a barrier, deterring any intruders from getting access into your home. If the distance between the window and the door is large, you might prefer a security screen that also has windows. This will give you the best of both.

2. Sagging

uPVC is a durable energy-efficient, cost-effective and economical alternative to timber sash windows. As time passes, they may develop a number of problems, including sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to lose its shape, it's crucial to act fast to prevent the problem from worsening.

To fix a window that is sagging you can try repositioning the hinges. To do this, you'll need open the window to access the frame. After that, using the screwdriver, you'll be able to unscrew the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, shut your window and verify the fitting. If you are happy with the size of the window, you can tighten screws to keep them in place.

If you can't reposition the hinges, you may need to replace the seal. Over time, Upvc Window Repairs rubber seals lose their elasticity and become dry and cause their tightness to decrease. It is crucial to replace your seal as quickly as you can in order to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also loosen. This is usually due to screws that have become undone over time, but it can be due to the mechanism of the handle wearing out. It's fairly simple to fix a loose uPVC handle. First, you'll need to close the window and perform a test fitting. The joint at the corners of the sash must align with the joint on the casing. If it isn't then you can use the screwdriver to loosen the handle. Then, turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it's important to take action. The leaks of water through windows could cause structural damage to your home, and hinder your ability to control the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is damaged or is missing.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on the severity of the issue is, old caulking may have to be removed. It is essential to remember that when it is about uPVC window repairs, you should not be tempted to 'over-caulk and then make the area harder to clean and can reduce your energy efficiency.

Verify that the drainage holes are free of debris in them, and also ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious cases, you may need to replace the window repairs near me.

Mold spots and rotted sills are other signs of water leakage. The mold thrives in damp environments and is able to quickly spread throughout the home.

If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal than the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with ease It could be the hinges that are at fault. They can be easily replaced by any competent DIYer and can be completed in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that have hinges and, like all mechanical parts, they can wear down over time. The process of replacing a hinge on a window is essentially a very simple process, but it's simpler when you have a person to assist in holding the frame in place.

Check that the uPVC hinges are open and closed in the proper direction. This can be done by looking for the arrow on each hinge. This indicates which way the window should open.

Window hinges that aren't working properly could be caused by improperly opening the window in a particular way or by poor installation at the factory. Sending us a photo through our website can often solve the issue. We are happy to offer advice.

It is also crucial to lubricate the hinges on a regular basis. This can be done by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window to operate and close more smoothly. It can also prevent corrosion and decrease the chance of sticking. It is recommended to do this at least once a year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different factors. Firstly the hinges, again because of wear and tear, could become misaligned. This can cause an opening to appear where the sash joins the frame. If they are beyond repair, it could be necessary to have them realigned. The second is the interlock, which is on the hinge side of the window, may also become misaligned, again it is feasible to give them a good clean, but in certain cases, it may be necessary to have them replaced.

The seals may wear out or become damaged over time, allowing air escape. Installing high-quality weatherstripping is a good way to stop draughts. Replace the upvc windows with low-emissivity glass. This will help to regulate indoor temperatures, and reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are typically fabric tubes filled with a filler that can be put on top of your window sill. These will keep your home warm by blocking out cold air.

The windows made of upvc can remain a great source of insulation and security to your home with a little regular maintenance and repairs. However, it is important to recognize that windows last for a certain period of time and there may come the point when it's more cost-effective to replace them rather than repair them. If you encounter any issues with your Upvc window, it's best to consult an expert as soon as possible.