Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they do not corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will reduce costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and may even be fatal. It is essential to take the time to ensure that you are doing everything you can to ensure that your windows are in good repair.

Single-pane windows are relatively easy to replace and typically fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this instance you'll need locate some plastic spacers that will help the new pane to fit correctly into the window frame.

If you're planning to attempt to remove the window panes by yourself it is important to wear the proper safety gear that includes gloves with a thick layer of material and protective eyewear. It is also an excellent idea to lay down a drop cloth before you start working on the glass to ensure that any shards will fall onto the cloth instead of onto the floor where they can be trodden under and cause further damage.

It's a great idea to tape the gap once the glass is removed. This will prevent drafts and water from entering your home until a professional comes out to repair the window. It also acts as a barrier, deterring any intruders to gain access into your home. If the gap is large, you might think about an alarm door that comes with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber sash windows. Over time, they can be affected by a variety of issues such as sagging. A sagging uPVC window could cause issues with light, draughts and even security. It is crucial to act when you discover that your uPVC windows are falling down.

Repositioning the hinges can aid in fixing a window which is sliding. To do this, you'll have to open the window to access the frame. With an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and check for fitting. If you're satisfied with the fit of your window, you can tighten screws to secure them in place.

If you aren't able to move the hinges you may require replacing the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to loosen. It is essential to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

UPVC handles can also loosen up. Most often it is due to screws that have come loose over time. However, it could also happen because the handle mechanism has worn out. It's relatively easy to fix a loose uPVC handle. First, you'll need to close the window and then perform an experiment fitting. The joints at the corners of the sash should align with the joint on the casing. If it isn't then you can make use of a screwdriver to loosen the handle and turn the mechanism back into its original position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains it's important to take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by any DIYer who has the ability. Depending on how serious the problem is, the old caulking may have to be removed. It is crucial to remember that when it is about uPVC window repairs, you should not be tempted to apply too much caulk and then make the area more difficult to clean and can reduce your energy efficiency.

Check that any drainage holes do not have debris inside them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more severe situations, you may have to replace the window.

Mold spots and rotted sills are another sign of water leakage. This mold thrives in damp environments and can quickly spread across the home.

It is also important to note that if the leak is coming from between the glass in your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sagging. It is also possible to be fixed by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and UPVC Window Repairs open with a breeze It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and are usually completed in just a few minutes.

Almost every household in the UK will have either top hung or side-hung uPVC windows that are hinged and like any mechanical part they will wear out over time. It's easy to change a window hinge but it's much easier if someone helps hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The issue can be caused by opening the window improperly or by a poor installation in the factory. Sending us a photo via our website is often enough to solve the issue. We are happy to offer advice.

It is also important to grease the hinges on a regular basis. Applying a light engineering lubricant to the hinges is a great way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window operate and close more smoothly. It can also prevent corrosion and decrease the chance of sticking. It is recommended to perform this every year. WD40 and other solvent-based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few different things. First, the hinges because of wear and tear, could become misaligned. This will cause a gap to form where the sash joins the frame. If they are damaged beyond repair, it may be necessary to have them realigned. The interlock may also become disaligned. This is located on the hinge's side and might require to be cleaned. In certain instances it might be necessary to replace the hinges.

The second most frequent reason for draughts is window seals. They can become worn down or damaged over time, and will allow air to escape through the gaps. Installing high-quality weatherstripping will help to keep draughts at bay. Replace the upvc window repair windows with low-emissivity glasses. This will help regulate indoor temperatures and decrease the risk of draughts.

The final method to cut down on the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler, which can be hung over your window sill. They will keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security for your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually wear out and it may be more cost-effective to replace them rather than repair them. So, if you're experiencing issues with your Upvc windows, it's recommended to seek assistance from a professional immediately.