Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain and are durable and long-lasting. They don't decay or rust as aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will save you from costly repairs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a great deal of damage to your home, which can make it very dangerous and potentially fatal. It is essential to make sure that your windows are in good working order.

For single pane windows it is relatively easy to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. If you have double-paned windows which are held together by internal beading, it is harder to remove and replace the old panes. In this instance you'll need to locate some plastic spacers that aid the new pane in being able to fit correctly into the frame of the window.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and UPVC window repairs not on the floor and could be trampled.

Once the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to stop water and drafts from entering the home until a professional comes out and fix the window. This will also act as a barrier that will prevent any intruders to gain access into your home. If the gap is particularly large, you might think about the security door with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber windows with sash. In time, they could develop a number of problems such as sliding. A window that is sagging can cause problems with light, draughts, and even security. It's important to take action as soon as you discover that your upvc repairs windows are sagging.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll have to open the window to get to the frame. After that, using a screwdriver, you can remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, shut your window and verify the fit. If you're satisfied with the fit of your window, tighten the screws to secure them in the right position.

If you aren't able to move the hinges, you may need to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to lose tightness. It is important to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also loosen. This is usually due to screws that have loosened over time, but it can also be due to the handle mechanism getting worn out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to close the window and do a test fitting. The joints at the corners of the sash must align with the joint on the casing. If it doesn't then you can use the screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

If you awake to wet floors and damp walls each time it rains, it's crucial to take action. Water leaks from windows not only lead to the degradation of your home's structure but also hamper your efforts to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant around the frame is either damaged or not present.

This is a simple fix that can be completed by any DIYer who is competent. Based on the severity of the problem the caulking that was used up may require removal before a new layer can be put on. It is important to remember that when it comes to uPVC window repairs, do not be tempted to apply too much caulk and then make the area harder to clean and can decrease the efficiency of your energy usage.

Verify that the drainage holes do not have debris in them and ensure that the sill pan has been angled correctly to drain away from the window. In more serious situations, you may have to replace the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in damp conditions and can quickly spread across the house.

If the leakage occurs between the double-glazed window, UPVC window repairs it is more likely that the problem is with the seal than the frame. This can be easily fixed by a uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open in a breeze, it may be the hinges that are at the fault. These are easily repaired by any DIYer who is skilled and are usually completed in just a few minutes.

Like any mechanical component hinges will wear out over time. The process of replacing a hinge on a window is essentially a simple process but it can be simpler when you have a person to assist in holding the frame in place.

It is also important to verify that the uPVC hinges are being opened and closed in the correct direction. This can be done by looking for the arrow on each hinge. This indicates the direction in which the window should open.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a particular way or by poor installation at the factory. This can often be resolved by sending us a picture via our website and we will be pleased to offer you advice.

It is also crucial to lubricate the hinges on a regular basis. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window to operate and close more easily. It also decreases the chance of windows sticking and help prevent corrosion. This must be done at a minimum once a year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. The hinges can also be disaligned as a result of wear, causing gaps where the sash and frame meet. These can be easily fixed by giving them a thorough clean, however when they're beyond repair, it could be necessary to have them aligned or replaced. Second, the interlock can also become misaligned. It is located on the hinge's side and could require to be cleaned. In some instances it is possible to replace them.

The next most common reason for draughts are the window seals, these are prone to wear or damaged over time and will allow air to escape through these gaps. Replacement of these with high-quality weatherstripping can help prevent draughts. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures and decrease the possibility of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler that can be placed over your window sill. They will keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security to your home with regular maintenance and repairs. However, it is important to recognize that all windows have a lifespan and eventually, they will reach a point where it is more economical to replace them than repair them. If you are experiencing problems with your upvc windows, it is recommended to seek assistance from a professional as soon as possible.