Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are easy to maintain and durable, as well as long-lasting. Unlike timber and aluminium, they are not susceptible to get rusty or decay.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will reduce repair costs as well as improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home, and could even be fatal. It is crucial to take the time to ensure that you're doing everything you can to keep your windows in good shape.

Single-pane windows are relatively easy to replace and will usually fit into the frames that were previously in use very easily. If you have double-paned windows that are joined by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this instance you'll need to locate some plastic spacers that will assist the new pane to fit correctly into the frame of the window.

If you're planning to try to remove the window panes yourself it is crucial to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a dropcloth before you begin working on the glass, installing so that any shards fall onto the fabric rather than on the floor, where they could be trodden under and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to block water and installing drafts from entering the property until a professional can come out and repair the window. This will also provide a barrier to prevent any intruders from making their way into your home. If the gap is large, you might be interested in an alarm door that comes with an integrated window as it offers the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash windows. However, over time, they can suffer from a variety of problems including sagging. A window that is sagging can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to stop the issue from getting worse.

Repositioning the hinges can aid in fixing a window that is sagging. To do this, you'll need open the window to get to the frame. Then, you can remove the hinges at the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window repair near me to test the fit after you've relocated your hinges. If you're satisfied with the fit, you can tighten the screws until they remain in position.

If you are unable to reposition the hinges you may require replacing the seal. Rubber seals may dry out and lose their elasticity over time, leading them to loose their elasticity. If this happens, it's crucial to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and safe from drafts.

uPVC handles can also become loose. This is often caused by screws that have become undone over time, but it could be caused by the handle mechanism wearing out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to close the window and perform an initial test to ensure that it fits. The corner joints of the sash need to be aligned with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it is important that you take action. Leaks of water from windows can cause structural damage to your home and hinder your ability to control the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant around the frame is either damaged or is missing.

This is a fairly simple fix and should be undertaken by any skilled DIYer. Depending on the severity of the issue the caulking that was used up might need to be removed before a fresh layer can be put on. When it comes to uPVC repair, you must be careful not to over-caulk. This will only make your window more difficult to clean and reduce its energy efficiency.

Make sure that the drainage holes are free of debris in them, and also ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious instances, you might have to consider replacing the window.

Mold spots and rotten sills are another sign of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

If the leakage is occurring between the double-glazed glass, it is more likely the issue is with the seal than the frame. Again this can easily be repaired by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open in a breeze, it may be hinges that are at the fault. They can be replaced by any competent DIYer and can be completed in just a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that use hinges and like any mechanical part they are susceptible to wear and tear over time. It is very easy to change a window hinge, but it's easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the correct direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The issue could be caused by opening the window incorrectly or due to a poor installation in the factory. Sending us photos through our website can often resolve the problem. We are more than happy to give suggestions.

It is also crucial to ensure that the hinges are lubricated on a regular basis. Applying a light engineering lubricant to the hinges is a good method to accomplish this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also stop corrosion and reduce the risk of sticking. This is recommended to be done at least once a year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. The hinges may also become misaligned due to wear, causing gaps where the sash meets frame. If they're beyond repair, it could be required to realign them. Secondly the interlock, this is located on the hinge of the window repairs and can be misaligned. Again, it is possible to give them a good clean, but in certain cases, it may be necessary to get them replaced.

These seals can wear down or be damaged over time, allowing air escape. Installing high-quality weatherstripping is a good way to stop draughts. Another option is to replace the window with glass that is low-emissivity, this will help to regulate indoor temperatures, and also lessen draughts.

One of the most effective ways to reduce drafts is to use an draught excluder. These are typically made of fabric which are filled with a sort of filler and can be positioned on the windowsill on top. These will help to stop cold air from entering and keep your home warm and cozy!

With a bit of regular maintenance and repairs your windows made of upvc will continue to provide an excellent level of insulation and security for your home. It is essential to remember that all windows eventually wear out and it may be cheaper to replace them than to repair them. If you are experiencing issues with your window made of upvc it is recommended to speak with a professional as soon as you can.