UPVC Window Handle Replacement

It's simple to repair a broken window handle with the proper tools. It's important to identify the kind of handle you have as well as the size of its spindle before purchasing an alternative.

Older uPVC window handles have a spur which protrudes and locks over the wedge striker. They can be left- or right-handed and should be matched when replacing.

What type of lock or handle do I have?

There are many upvc window locks and handles each with its own advantages and purposes. The type of handle you are using will determine how easy it is to open your windows and if the locking mechanism works in the way you want it to. Over time, and with regular use the upvc handles that are on your windows may be damaged and worn out. This makes them less secure and Window Handle Replacement less effective. In certain instances, they might even fall off completely. It is important to repair your window handles made of upvc immediately if you notice they are falling off. This will help prevent burglaries and will keep your home safe.

It's a task that virtually anyone can perform. You will need some basic tools, but with proper knowledge, it's simple and should take only a couple of minutes. To begin you must identify the type of handle and lock you have on your window to help you to find the ideal replacement.

Inline Espagnolette Handles

These are the most common kind of upvc handle and are usually located on the other side of your window. They are flat in design and feature an opening that is connected to the locking mechanism on the frame of the window when it is turned. Inline upvc handles also have a spindle that runs through the centre of the handle and then into the frame of the window to operate the latch.

Cockspur Handles

They are usually found on older uPVC windows and have distinct hook-shaped designs. Cockspur handles have a single screw that is used to secure the handle to the frame and are not as secure as other kinds of window handles.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles because they can be turned to open the window and then tilted to the window to let air circulate. They typically have a 7mm spindle on the side of the handle. They are available in both left and right handed versions.

When you are purchasing replacement handles for upvc It is crucial to verify the length of the spindle because not all handles are identical in size. Drop something into the middle of the hole to measure the length. This is the longest spindle length that will fit your window.

What is the spindle?

uPVC window handles operate similarly as doors. By turning the handle, you will be able to activate a latch inside the frame. The window can then be opened and closed. The handles can become damaged, Window Handle Replacement especially if they're used frequently or exposed to harsh conditions. This can lead to the need to replace your uPVC handles for windows as they may not be able to operate the window correctly in the future.

There are many types of uPVC handles, including Espag, Cockspur, and Spaded handles. These handles are designed in a variety ways to fit into uPVC frames. Each handle style uses a different spindle to lock the window mechanism. This is why it is crucial to identify the type of handle is installed on your uPVC window so you can find the right replacement for it.

The base section of the handle will tell you what kind of uPVC it is. A snap-in covers should be over the screw that holds the base of the handle in place. After removing this and you'll be able to see the screw that holds the handle base in position. Once both screws have been removed then you should be able to take the handle out of the uPVC.

After removing the uPVC handle, remove it from the locking mechanism. Take note of the length of the spindle. You will need to purchase a replacement with the same length as the original handle and locking device.

The main issue with most window handles made of uPVC is that the spindle gets worn out and can no longer function properly with the locking mechanism. This can be caused by corrosion, damage due to constant use or a loosening locking mechanism. If this happens, you'll have to replace upvc window handle both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the handle that was previously attached?

Window handles are susceptible to being damaged or destroyed over time. It is important to repair them as quickly a possible to ensure your security. It is easy to replace a worn or damaged handle. The task can be completed in less than one minute without the need for special tools.

The first step to remove the handle that was previously used is to remove the screw situated at the top of the base of the handle. After this screw is removed, the handle can then be pulled away from the base. Another screw will be located at the bottom of the handle. This can also be removed. Once the two screws are removed, the handle will be detached from the base of the window.

Once the old handle has been removed, you can take the new handle and line up the fixing holes with the holes that are present in the window frame. There may be a tiny sticker or caps on the new handle, so take off them if needed and then screw the handle in its place. It is important to check that the handle is working after it is installed. Turn the handle around and ensure that the lock mechanism is working.

Espag handles have spindles that protrude out of the handle and slot into the multipoint locking mechanism that is on the frame of the window. Cadenza windows feature a blade with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that hooks over either the outer frame or transom bar cross member in the window.

Once you have installed the new handle, slide the spindle inside the window lock and tighten it. Once the handle is firmly fixed in place and secured, replace the snap-in cover and the screw cap (if appropriate). When the handle is ready to use, you can open and close the window a couple of times to make sure it is working correctly and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult and the process is simple. You only need an screwdriver and a bit of perseverance. First, ensure that the handle is not locked. Then, remove any visible screws. You could also replace them with screw caps. After the handle has been removed, you need to make a note of the length of the spindle which protrudes from the back of the handle. This is crucial since it will determine the kind of handle you'll need to buy.

Espagnolette handles are the most common type of handle for uPVC windows. They feature a spindle that runs through the handle and operates a locking mechanism inside the window frame. The handle releases the latch, allowing the window to open. During regular use and over time, handles for espagnolette may be damaged.

Cadenza handles are a second type of uPVC window handle commonly used on tilt and turn windows. They feature an elongated blade that functions as a multipoint locking mechanism within the window. They are more secure than the espagnolette handles since they only open from the inside. They can be replaced using the same procedure as you would with espagnolette handles however, ensure that the new handle is angled, not flat.

After you have chosen the right handle, simply align the new handle with the existing screw holes prior to fixing it with screws. You should then put the screw covers back on and make sure the new handle functions correctly. You can accomplish this by moving the handle back and forth from the locked position to the unlocked one for a few times. It might be worthwhile to speak with an expert to see whether you can solve any problems. They are often able to advise you on the best approach to resolve the issue in a quick and effective manner.