Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like aluminum and timber.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home, and could even be fatal. It is important to take the time to make sure that you are doing everything you can to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace windows, and the new one will usually fit inside the old frame very easily. However when windows with double glazing repair panes are secured by internal beading it will be more difficult to remove the existing panes and install new ones. In this situation, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall onto the fabric and not onto the floor, where they could be trampled under.

Once the glass is removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from getting into the home until a professional can come out and repair the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the distance between the window and the door is large, you might prefer security screens that has a window. This will give you the best of both.

2. Sagging

uPVC is durable, energy-efficient and window doctor near Me affordable alternative to timber sash window. However, over time, they are susceptible to a range of problems including sliding. A sagging window in uPVC can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's important to act quickly to prevent the problem from getting worse.

To fix a window that is sagging you can try to reposition the hinges. To accomplish this, you'll have to open the window to access the frame. You can then unscrew both the hinges at the top and bottom with a screwdriver and adjust them clockwise or counter-clockwise. Close your window to check the fit after you've moved your hinges. If you're happy with the fit, tighten the screws until they remain in position.

If you cannot reposition the hinges, you could have to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, which causes them to lose their tightness. It is important to replace your seal as quickly as you can in order to ensure that your uPVC window waterproof and window Doctor near Me draughtproof.

UPVC handles can also become loose. Often, this is caused by screws that have become loose over time. However, it can occur because the handle mechanism has worn out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to close the window and then perform a test fitting. The joints at the corners of the sash must align with the joint on the casing. If it isn't you can use a screwdriver to loosen up the handle. Then, turn the mechanism to position.

3. Water Leaks

It is important to take action if awake each day to discover mouldy walls and floors that are wet. Water leaks from windows are not just a cause for destruction of your home's structure but also undermine your efforts to regulate the temperature in your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or is missing.

This is an easy fix that can be done by any DIYer who has the ability. Depending on how severe the issue is, the old caulking might need to be removed. When it is time to uPVC repair, it is important to avoid 'over-caulking'. This will make your window more difficult to clean and lower its energy efficiency.

Verify that the drainage holes have no debris in them and that the sill pan is properly angled to drain away from the window. In more severe situations, you may have to replace the window.

Mold spots and rotted sills are also signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to remember that if the leakage originates from the glass of your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sagging. It is also possible to be repaired by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open in a breeze it could be hinges at fault. They can be easily replaced by any competent DIYer and can be done within a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that are hinged and, just like any mechanical component they can wear down over time. It's very simple to change the hinges on a window, but it's easier if someone else helps hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. Look for the arrows on each hinge to determine which direction the window Doctor near me should be opened.

The problem with the hinges on windows could be caused by improperly opening the window a certain manner or because of poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are more than happy to provide advice.

Regularly lubricating the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window to operate and close more smoothly. It also helps prevent corrosion and decrease the chance of sticking. It is recommended to do this once a year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different factors. The hinges may also become misaligned due to wear, creating a gap where the sash meets frame. If they are beyond repair, it could be necessary to have them realigned. The second is the interlock, which is on the hinge side of the window, can be misaligned. Again, it is possible to just give them a good clean, but in some instances it could be necessary to have them replaced.

The second most frequent reason for draughts are the window seals. These are prone to wear or damaged over time and let air escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help to regulate indoor temperatures and lessen the possibility of draughts.

Another method of reducing draughts effectively is by using a draught-excluder. These are usually fabric tubes filled with a filler which can be hung over your window sill. These will help to keep cold air out and keep your home warm and cozy!

With a little regular maintenance and repair your windows made of upvc will provide a great level of security and insulation for your home. However, it is important to recognize that all windows have a lifespan and eventually, they will reach the point when it's more efficient to replace them than repair them. So, if you're having issues with your upvc windows, it is always best to seek professional assistance as soon as possible.