Reasons Your fiat Van key replacement 500 Key Fob Won't Work

A fiat panda key programming 500 key fob makes it simple to open doors and start your vehicle. There are a myriad of reasons why the key fob might stop functioning. It could be due to a dead battery or damage to the receiver module, water problems, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). Includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't function is due to a dead battery. Modern key fobs come with a limited operating range and must be within some feet of the vehicle in order to function. If you're far from your car and push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) with a new battery of a trusted brand such as Panasonic Duracell or Energizer. You can typically find them at your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your Fiat 500. The car will flash its parking lights, and the key fob should operate the lock and unlock switches.

If your fob's key does not work after replacing the battery, it may be water damage that prevents it from interacting with the module in your vehicle. Water damage can happen in many ways, such as an easy splash or submerging the key fob in saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this isn't working, you'll need to have the fob changed by an auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not the best idea to submerge the fob in water however, don't give it up if you accidentally drop it in water or forget to take it out of your pants pocket.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Next test the fob to test if it works. If the fob doesn't work, it may need to be programmed again. This is usually done by a professional or dealer auto locksmith.

If your key is a bit older and is not programmed to work with your vehicle You will need to replace it completely. A professional automotive locksmith can carry out this simple task. The locksmith will need the key cut to match your car's ignition. They'll also have to program the fob into the system of your car. This is a cheap and fast process that can be completed within the same day.

Receiver Module Issues

The 500 key fob could be inoperable because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. You can solve this issue by moving the remote closer to your car until it responds.

If your fob isn't working after you replace the battery in the coin, also known as a "button", "watch" or "button" or "button", it may be due to a malfunction on the internal circuit board. In most cases, reprogramming the fob can resolve the problem. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare instances it is possible that the fob will become desync'd with your vehicle due to software issues or hardware issues. This could be a huge problem, but you can often fix this by visiting an auto locksmith to have them reprogram your fob for you. In some cases it may be necessary to reinstall the software on your body control module, as well.

Interference

In addition to a dead battery on a coin The key fob may not be able to transmit or Fiat Van Key Replacement receive the signal due to interference. This can happen when the key fob is close to a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not work include a poor connection to the buttons and internal chip or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands that are then interpreted by the vehicle.

Fortunately, there's an easy method of resetting all on-board systems in your 500 keys, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers. This can help the key fob to function again. If the issue continues you should speak with a certified technician. They will be able diagnose the exact cause of issues.