How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models has an entry system that is keyless into. The key can be compared to an remote control, and is able to be replaced with a new one from a Kia dealer or locksmith.

Key fobs may stop working due to a number of reasons, such as a dead battery, worn-out buttons signal interference, or water damage. Here are some tips on how you can get your Kia Sportage replacement key to work again.

How do you replace the remote key or smartkey?

No matter if your Kia is equipped with an intelligent key, remote key push to start key or regular metal non-transponder key, the battery in these keys will eventually need replacing. This is particularly when your car shows a message that states the smart or remote keys aren't powered.

This is a relatively easy process. To replace the keyfob battery take out your mechanical key from the slit that is located at the back of the fob. Then, pull the cover open. A small screw is found inside the key fob to hold the battery in its place. Using a small screwdriver, loosen the screw and remove the old battery. Install the new battery and then close the gap on the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a programming machine, which is only available to the automotive locksmith or dealer. Other keys (non transponder keys made of metal) don't require programming. If your key needs to be reprogrammed, then you will need to know the key code number written on the key code tag and record it in a safe location.

How do you replace a battery?

If the Kia key fob does not respond when you press the lock/unlock button, it is most likely that the battery is depleted. A low battery may also cause other issues such as the check engine light turning on or delayed engine cranking. Fortunately replacing the battery on the key fob is a relatively easy DIY task that requires only the most basic tools.

Before you begin the process before beginning the process, ensure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece at the bottom of your key fob and jiggle it until a metal key slips out. You can then insert this key into the door handle of the driver to open your car.

To replace the battery inside the key fob remove the cover at the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery, and then align the new one to ensure that the "+" positive side is facing you, and the "-" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts on the metal.

After you have installed the new battery after which you turn the key fob off and on in the ignition until the door locks cycle. Then, you can test your Kia key fob and see whether it's working again.

How do I replace a smart keys

You can have an ordinary keyfob or Smart Key based upon the model of Kia Sportage. The difference between the two is that the smart key comes with a small mechanical key blade in it, whereas the standard fob isn't equipped with. Both key fobs are equipped with batteries that eventually require changing. Fortunately, this is a fairly simple process that takes only two minutes.

Before you start it is important to ensure that you're on a flat surface with good lighting and that your kia key replacement is turned off. Keep in mind that there are tiny components inside the fob which could fall out if you are not cautious.

The first step is to locate the small release button on the back of the lower part of the fob. This will be either a circular or rectangular slot. When you press it, the mechanical key blade will pop out and you will be able to open the key fob.

Once you have the key fob open, you can simply take out the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you're done, the key fob should allow you to lock, unlock, and start your vehicle, even if it isn't running.

How do you replace the mechanical key?

The Kia key fob is a fantastic feature that lets us lock and unlock our car at the touch of one button. However, like all devices it may have issues occasionally. Luckily, there are ways to solve these issues and keep our key fobs in good working condition for the long term.

One of the most frequent problems is a dead or dead battery. This could cause the fob to stop working entirely or stop working at times. If this is the problem you should replace the battery a new one.

If this does not solve the issue, try using the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not to harm any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new battery.

After the new battery has been put in, close and then open the doors with the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and ensure that it's working correctly. If the fob isn't functioning, contact a locksmith or dealer to solve the problem. To avoid lockouts in the future, ensure you have an emergency key that can work in all of the door and trunk cylinders.