Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain and durable, as well as long-lasting. Unlike timber and aluminium, they don't rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home, and could even be fatal. You should take the time to make sure that your windows are in good shape.

Single-pane windows are relatively easy to replace and typically fit into old frames very easily. However, if windows with double panes are secured by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this case, you will need to find some plastic spacers to help the new pane to fit perfectly into the frame of the window.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards of glass fall onto the fabric and not onto the floor which could cause them to be trampled under.

It's a great idea to tape the gap once the glass is removed. This will keep drafts and water from getting into your home until a professional comes out to fix the window. This will also provide an obstacle to stop intruders from getting into your home. If the gap between the window and the door is substantial, you may want to use an alarm system that has a window. This will give you the best of both.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows with sash. Over time, they can be affected by a variety of issues that include sliding. A sagging window doctor near me can cause problems with light, draughts and even security. It's important to take action when you realize that your uPVC windows are sagging.

To fix a sagging window you can try repositioning the hinges. You'll first need to open the windows so you can reach the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust them counter-clockwise or clockwise. After you've repositioned the hinges, close the window and check for fit. If you are happy with the size of the window, tighten the screws to secure them in the right position.

If you aren't able to move the hinges you may need to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's essential to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and draught-proof.

uPVC handles can also become loose. This is typically caused by screws that have become undone over time, but it could be due to the handle mechanism wearing out. It's relatively simple to repair a loose uPVC handle. The first step is to close the window and then perform an experiment fit. The corners of the sash need to align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and return the mechanism to its original position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it's important to take action. The leaks of water from windows do not only lead to the destruction of your home's structure but also undermine your efforts to control the temperature in your home. Most of the time, uPVC window doctor near me leaks are caused by damaged or missing sealant.

It is a fairly easy fix that can be done by any competent DIYer. Depending on how severe the problem is, the old caulking may have to be removed. It is crucial to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk and then make the area more difficult to clean and can reduce the efficiency of your energy.

It is crucial to make sure that the drainage holes are free of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotted sills are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage occurs between the double-glazed window, it is more likely the problem is related to the seal, not the frame. This can be easily repaired by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with ease it could be hinges that are at fault. These are easily repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Like any mechanical part, hinges can be damaged over time. Changing a window hinge is essentially a very simple procedure, but it is simpler with someone else to assist in holding the frame up.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. Check for the arrows on each hinge to determine which direction the window should be opened.

The issue can be caused by opening the window incorrectly or a faulty installation at the factory. Sending us photos through our website can often solve the issue. We are happy to give suggestions.

Regularly lubricating hinges is also essential. Applying an engineering lubricant that is light to the hinges is an ideal method to accomplish this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It can also lower the risk of a window sticking and help prevent corrosion. Ideally, you should perform this every year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a few various factors. The hinges can also become disaligned as a result of wear, which can cause a gap where the sash meets frame. If they're beyond repair, it might be necessary to have them realigned. Secondly the interlock, this is on the hinge side of the window and can also become misaligned, again it is possible to just give them a clean but in some cases it might be necessary to have these replaced.

The next most common reason for draughts is window seals. These are susceptible to being worn out or damaged over time, and allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help control indoor temperatures and decrease the risk of draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler that can be placed over your window sill. They will help block out cold air and keep your home warm and cozy!

With a bit of regular maintenance and repair your windows made of upvc will continue to provide an excellent level of insulation and security for your home. It is important to remember that all windows will eventually wear out and it could be more cost-effective to simply replace them than to repair them. So, if you are experiencing issues with your Upvc windows, it's best to seek professional assistance as soon as you can.