Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to experienced auto locksmiths who have the proper equipment and know-how. They can design and program keys quicker and more efficiently than dealerships.

A dead battery for your coin is most likely to be the cause when your key fob stops locking or unlocking the doors. There are other causes that the key might be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the scenario, you'll need utilize the backup starting method that is described in the owner's manual to your vehicle.

Another reason why your 208 may not start is because the spark plugs are been damaged. The spark plugs are responsible to ignite the fuel that starts the engine. However they are limited in their time of life. They will eventually break down if they aren't used frequently enough.

Luckily, there is an easy solution to this problem. Check the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts, it's time to replace it. It is also necessary to clean the contacts of the battery if it has corrosion. This can be done by lifting the rubber covers that protect the two terminals on the battery and using wire brushes to clean any corroded parts of the battery. Then, you must reconnect the positive and negative pole cables.

Water Damage

If your 208 doesn't start and the battery has not fallen flat, it is time to inspect the spark plugs. It is possible that they are just overly dirty, which causes them not to spark. The spark plugs can be cleaned in an workshop.

Peugeot cars are equipped with transponder keys that works with the car's ignition system. This ensures that only the correct key can start the engine. If the chip inside the Peugeot key is damaged then it won't send the correct signal to the vehicle.

This is a very common issue that is often caused by water damage. This is particularly prevalent in colder climates where the vehicle might have been exposed to rain or snow. In this situation, contact a reputable locksmith who will have the necessary tools and equipment to change the key's programming. They also have the most up-to-date technological know-how and machinery required to create the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips with a new version that makes use of electronic components that are mounted on a circuit board. The new system works great in its initial state, but the circuit boards wear out over time and cease to function properly.

This could stop the immobiliser's function from being activated, meaning your vehicle won't start. Contact a Peugeot specialist or a locksmith, if this is the case.

A common issue occurs when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A locksmith for cars will replace the battery and then cut a new key blade for you. This is a simple solution.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the floor, or being exposed to a sudden rain or accidentally washing it or washing it, it could be due to a faulty receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that block water from getting to the chip inside. However, prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob in sea water at the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working it is necessary to have the module replaced. This is only completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys, peugeot 208 key replacement unlike other cars, are secured by an immobilizer system. This requires the proper code to begin the car. This is why you must go with a knowledgeable Peugeot locksmith for the job of creating and programming a replacement.

Computers with faulty on-board computers

The on-board computer in your Peugeot is responsible many systems in your car, including power windows and airbags. The on-board computer will show a code if something goes wrong. This code is saved in the system and will stay there until the issue has been resolved. This will often require the on-board computers to be replaced.

The most typical reason for the warning light for the airbag to illuminate is corrosion or loose connections in the sensor. This can be caused by wear and tear, ageing or exposure to salt and moisture. This issue should be dealt with as soon as you can, since an airbag that is not functioning could pose a risk in the event in the event of an accident.

If your Peugeot is showing a card detected as not present error, then the key battery in the key fob could be dead or weak. This prevents the key fob from transmitting a signal that will disable the standard immobilizer in your vehicle. Test this by pressing the unlock button on the key fob, and then trying to start your car. If this fails it is likely that the battery is in need of replacement.