Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they don't get rusty or decay.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and may even be fatal. It is essential to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace, and they will usually fit into the old frames very easily. If you have double-paned windows that are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this situation you'll need locate some plastic spacers to assist the new pane to fit correctly into the window frame.

Wearing eye protection and thick gloves is essential if you plan to remove the glass by yourself. It is also a good idea to lay down a drop cloth before you start working on the glass so that any fragments of glass fall on the fabric rather than on the floor, where they could be trampled upon and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional is able to come out and fix the window. It also acts as a barrier, preventing any intruders from gaining entry into your home. If the gap is large, you might want to consider using the security door with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time they can suffer from a variety of issues, including sliding. A sagging uPVC windows could cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to prevent the problem from becoming worse.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows to access the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after having repositioned your hinges. If you're happy with the fit, uPVC window repair tighten the screws to ensure they stay in position.

If you are unable to reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and uPVC window repair become dry, which causes them to lose tightness. If this happens, it's essential to replace the seal as fast as you can to ensure that your uPVC windows are waterproof and safe from drafts.

uPVC handles may also become loose. This is usually due to screws that have loosened over time, but it could be due to the mechanism of the handle getting worn out. It's relatively easy to repair a loose uPVC handle. First, you'll need to close the window and perform a test fitting. The corner joints of the sash need to be aligned with the casing joint. If it doesn't, you can use a screwdriver or a wrench to loosen the handle, and then turn the mechanism back into the position it was in.

3. Water Leaks

If you wake up to wet floors and damp walls each time it rains it is important that you take action. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature inside your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is a simple fix that can be accomplished by anyone who is a DIYer with the skills. Depending on how serious the issue is, old caulking may have to be removed. It is crucial to remember that when it comes to upvc window repairs near me window repairs you should not be tempted to apply too much caulk in order to make the area harder to clean and could decrease the efficiency of your energy usage.

Make sure that the drainage holes have no debris in them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more extreme situations, you may have to replace the window.

Other indicators of water leakage are decayed sills and the appearance of black spots of mold on the walls near the window. This mold thrives in damp environments and can quickly spread across the house.

It is also important to note that if the leakage is coming from between the glass of your double glazed window repairs-glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sagging. Again this can easily be corrected by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your Upvc window repair windows are difficult to open, or loose and open with ease It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and are usually done within a few minutes.

Like any mechanical component hinges will wear out over time. It's very simple to replace a hinge on a window but it's much easier if someone helps you to hold the frame.

Verify that the uPVC hinges are open and closed in the correct direction. You can check this by checking for the arrows on each hinge. This indicates the direction in which the window should open.

The issue could be caused either by opening the window incorrectly or due to a poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are happy to offer assistance.

It is also important to ensure that the hinges are lubricated on a regular basis. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window to open and close more easily. It also helps prevent corrosion and reduce the risk of sticking. This is recommended to be done at least every year. WD40 or other solvent-based oils should not be used since they can damage your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. First, the hinges due to wear and tear could become misaligned. This causes gaps to develop where the sash joins the frame. If they are beyond repair, it could be necessary to get them re-aligned. Secondly the interlock, this is on the hinge side of the window, can also become misaligned, again it may be possible to just give them a good clean, but in some cases it might be necessary to get them replaced.

These seals can wear down or be damaged over time, allowing air escape. Installing high-quality weatherstripping is a good way to stop draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help regulate indoor temperatures, and reduce draughts.

Lastly, one of the most effective ways to reduce draughts is by using a draught excluder, these are usually fabric tubes filled with some sort of filler and can be put on top of your windowsill. They will keep your home warm by blocking out cold air.

With a bit of regular maintenance and repairs, your upvc windows will continue to provide excellent security and insulation for your home. It is crucial to recognise that all windows have a life span and there may come the point when it's more efficient to replace them than fix them. If you encounter any issues with your upvc window you should consult a professional immediately.