upvc window handle replacement (official source)

Replacing a broken window handle is a relatively easy process, and with the right tools it can be done quickly. But it's essential to know your handle's type and spindle length before buying the replacement.

Older uPVC windows have cockspur handles for windows. They have a spur that protrudes to the lock of a wedge cockspur striker plate. They can be left- or right-handed, and must be compatible when replaced.

What kind of lock or handle do I have

There are a variety of window locks and handles made from upvc each with its particular advantages and uses. The type of handle you have will determine whether or not your locking mechanism is effective and if it's easy to open the windows. Over time and through regular use, upvc window handles are prone to wear or damage. out, making them less effective and secure. In some instances they might even be completely removed. It is important to repair the handles on your window made of upvc when you see them falling off. This will help to prevent potential break-ins and ensure your home is secure.

It's a task that virtually anyone can perform. With just a few tools and the right information it's a straightforward procedure that should take no more than a couple minutes. To get started you'll need to identify the type of lock and handle you have on your upvc window, which will help you identify the best replacement.

Inline Espagnolette Handles

These are the most common type of upvc handles and are usually located on the other side of your window. They are flat in design and feature an opening that is connected to the locking mechanism on the window frame when turned. Inline upvc handles also come with spindles that run through the middle of the handle, and into the frame of the window to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are secured to the frame of the window with only one screw and are less secure than other types of window handle.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles because they can be rotated for opening the window, and then lowered to the window to let air circulate. They typically have a 7mm spindle at the side of the handle. They are available in left and right handed versions.

When you are purchasing replacement handles for upvc It is crucial to verify the length of the spindle since not all of them are the same size. To determine the length of your handle made of upvc, simply drop something in the middle of the hole and then measure how far it extends before meeting an obstruction. This is the longest spindle length that will be suitable for your window.

What is the spindle?

uPVC window handles operate similarly like doors. By turning the handle, you are able to operate a latch within the frame. The window is then opened and closed. However, sometimes handles can be damaged, particularly when they are used frequently or exposed to harsh weather conditions. This can lead to the need to replace your uPVC windows handles as they might not operate the window correctly anymore.

There are several different types of uPVC handles available comprising Espag, Cockspur and Spaded handle options. They are designed in a variety of ways to fit into uPVC frames. Each handle style uses an entirely different spindle for locking the window mechanism. It is essential to determine the kind of handle that is installed on your uPVC windows so that you can replace it with the right one.

You can find out what kind of uPVC handle you are using by taking a look at the base of your handle. There should be a'snap in' cover over one screw which holds the handle base in place. Remove this and then you should be able to see the second screw at the opposite end of the base section of the handle. After both screws have been removed and you are able to pull the handle from the uPVC.

Once you have removed the uPVC window handle, you will need to remove the spindle you have removed from the locking mechanism. Be sure to note the length of the spindle as you will need to ensure that you buy a replacement that has the same length as your original handle and locking mechanism.

The spindle wears down and is unable to operate the locking mechanism. This can be caused by corrosion, damage from frequent use, or an unreliable locking mechanism. If this occurs, you will need to replace both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the old handle?

Through time and regular usage, window handles could be damaged or destroyed, and when this happens, it is crucial to repair them as soon as possible to ensure the safety of your home. It is simple to replace a worn or damaged handle. The job can be accomplished in less than an hour without the need for any special tools.

The first step to remove the handle that was previously used is to remove the screw that is situated at the top of the base of the handle. After this screw is removed, the handle will be pulled away from the base section. Another screw will be located at the bottom of the handle. This too can be removed. After these two screws are removed, the handle can be detached from the window's base.

After removing the handle and fixing holes, align the holes of the new handle with the holes already present in the window frame. There may be a tiny cap or sticker on the new handle, so remove the caps if needed, and then screw the handle into place. It is essential to ensure whether the handle functions after it is put in place. Turn the handle over and make sure the lock mechanism is in place.

Espag handles come with an elongated spindle that extends from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hook over the frame of the window or the transom crossmember of the bar.

Once you have the new handle in place, insert the spindle inside the lock inside the window and then tighten it down. Replace the snap-in cover and screw cap (if necessary) once the handle is securely fixed. Once the handle is ready to use, open and close the window a few times to make sure that it functions properly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The procedure is easy. All you need is a screwdriver and a bit of patience. First, ensure that the handle that you are replacing is unlocked. Then remove any screws visible. You can also replace them using screw caps. After you have removed the handle, you'll need to record the length of the spindle which extends from the back. This is crucial as it will determine the kind of handle that you will need to buy.

Espagnolette handles made of uPVC are the most sought-after type of handle. They feature a spindle that runs through the handle and acts as an internal locking mechanism within the window frame. When the handle is turned it releases the latch on the window, allowing it to open. When used regularly and time, handles for espagnolette may become damaged.

Cadenza handles are another type of uPVC window handle that is commonly used on tilt and turn windows. They feature a protruding blade that operates a multipoint locking mechanism within the window. They are usually more secure than espagnolette handles as they are only accessible from the inside. They can be replaced by the same method as espagnolette handles but you must make sure that the new handle has a curved blade instead of flat ones.

Once you have decided on the right handle for UPVC Window Handle Replacement you, you can simply align the new handle with the existing screw holes and then screw it into the appropriate position. Then, put the screws on and test the new handle. This is accomplished by moving the handle from locked position to the unlocked and vice versa several times. If you have any issues, it may be beneficial to speak with a professional to see if they are able to assist in resolving the issue. They are often able to advise you on the best solution to solve the issue in a fast and efficient way.