Fiat 500 Replacement Key Fob

It may be time to replace the battery if your 500 remote key fob isn't working. If you replace the battery and it doesn't work the issue could be elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and spare parts required for this type of service.

Dead Coin Battery

The most common reason why your Fiat 500 key fob will not unlock or lock the doors is due to a dead battery. The key fob contains the battery of a coin-cell that will drain quickly if it is not frequented enough. If your remote has started to show signs of a loss in range or stopped functioning, then the battery may be dead.

Metal clips hold the battery in inside the key fob. If the clips aren't secure, they can cause contact issues which will prevent the remote from receiving power. Utilizing a small screwdriver, pull the clip that holds the retaining pin open to remove the battery and then insert a fresh one. Be sure to use an identical replacement battery kind of voltage, the same size and specifications as the original battery.

The key fob may also become corroded or damaged by water exposure. Even a short bath in soapy water can harm the electronic chip within. It's best to keep your key fob in a dry place.

Water Damage

Water damage could be the reason behind your key fob's inability to function properly. Key fobs are fitted with rubber seals that prevent them from being damaged by rain or a splash of water, however it is very important to keep your keys from being tossed into the pool, ocean, and the washing machine!

The key fob has an electronic chip that transmits a signal car's immobilizer system. The chip allows the 500 to lock and start. If it gets wet, however it will cease to work.

Try cleaning the internal electronics of your key fob using isopropyl alcohol, or an electronic cleaner to see whether they're still functioning. However, it's better to purchase a new one from a dealership rather than trying to fix the key fob that was submerged in salt water.

A replacement fob could cost you some money however, it's less expensive than paying to have your Fiat 500 towed to a dealer and repaired there! Plus, you can do it yourself in a few easy steps. Be sure to have the correct battery type before you attempt to open your keyfob. There are step-by-step directions for any car keyfob on the internet.

Faulty Chip

The chip in the key fob communicates with the immobiliser of your car to ensure that your vehicle will start only when the right keys are in place. If the chip is damaged or fiat 500 Spare key cut corrupted in any way the car won't start.

A damaged chip could occur due to a variety of reasons but the most common cause is water damage or a dead battery. Regardless of the reason, it's a good idea to leave this task to a locksmith since they can replace the chip fast and at an affordable price.

If your key fob stops working after exposure to clean tap water or rain, take off the battery and clean the electronic component using a paper towel to ensure that it is completely dry before putting it back in. If the key fob will not work, fiat 500 spare key cut there is the possibility that it's a fried component and needs to be replaced.

Some people will turn to their dealer when they are in need of a new Fiat key fob, but this is a costly alternative. United Locksmith is the best option for you if need your Fiat keyfob fixed at a reasonable price. We have the tools and experience required to repair your fiat punto car key 500 spare key cut (sneak a peek at this web-site.) key fob in a quick and professional manner.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle which will unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. There are a few reasons why the fob could not function. This includes a dead battery, water damage, worn-out buttons, a receiver issue, signal interference or malfunctioning chips.

If the fob was in a pocket which has suffered a severe trauma, such as being dropped on hard floor or being washed in a washing machine the fob may not be able to communicate with the car's Body Control Module (BCM). This is because the BCM is a secure system that can only accept a signal from a genuine original key and not accept any other.

You'll have to replace the fob in case this happens. A locksmith professional can handle all aspects of the replacement process and can even program a brand new one for your 500. In fact, they can provide you with a clone key that works just the same way as the original fob (and costs a fraction of the cost).