fiat 500 spare key cut 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it might be time to replace the battery. If you replace the battery, but it's still not working, the problem may be somewhere else.

United Locksmith specializes in the production of new keys for classic vehicles. We have all of the necessary tools and parts to provide this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob comes with an in-built battery that is prone to draining quickly when it isn't being frequented enough. If your remote started to show signs of weakening such as a loss in range, and then stopped working completely, the battery is probably dead.

The battery in the key fob is held in place with metal retaining clips. If the clips aren't secure, they can cause problems with contact, which can prevent the remote from receiving power. Use a flathead screwdriver remove the retaining clip and then remove the old battery. Make sure that the battery you choose to use has the same voltage, size, and specification as the original.

The key fob might be damaged or corroded through exposure to water. Even a brief bath in soapy, warm water can cause damage to the chip. It is recommended to keep your key fob in a dry place.

Water Damage

Damage to your water supply could be the reason behind your key fob not functioning properly. Key fobs come with rubber seals to protect them from being damaged by a light rain or splashes of water. However, it is essential to keep your keys away from the pool, ocean, and the washing machine!

The key fob has an electronic chip that transmits a signal to your car's immobilizer system. The chip is what allows the 500 to be locked and started. If it gets wet, however it will not function.

If you want to check if your key fob is functional you can clean the internal electronics with isopropyl or an electronic cleaner. It is recommended to replace a key fob if it has been submerged into salt water instead of trying to repair it yourself.

A replacement fob may cost you a bit however it's much less expensive than paying to have your Fiat 500 towed to a dealership and repaired there! You could also do it yourself by following just a few steps. Make sure you have the correct battery type prior to opening your keyfob. There are step-by-step directions for any car keyfob on the internet.

Faulty Chip

The chip in the key fob communicates with the immobiliser of your vehicle to ensure that the vehicle will only start when the right keys are in place. If the chip is damaged, or damaged in any way the car won't start.

Damage to the water or a dead phone battery are the most common reasons for a faulty chip. Whatever the reason, spare key for fiat 500 it's a good idea to leave this work to a locksmith, as they can replace the chip fast and at a low cost.

If your key fob does not function after being exposed to water that is clean from the tap or rain take it off the battery. Clean the electronic component with a paper towel. If the spare key For fiat 500 fob does not function, there is the possibility that it has a fried component and needs to be replaced.

Some people will turn to their dealer when in need of an entirely new Fiat key fob, however this is a costly alternative. If you are looking for a cost-effective way to have your Fiat key fob repaired then look no further than United Locksmith. We have the tools and experience necessary to repair your Fiat key fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle that can unlock and lock doors (and start the car for vehicles with an automatic transmission) up to 50 feet. However there are a few things that can cause the fob to cease functioning. It could be due to a dead battery or water damage or worn buttons as well as a receiver module problem, and signal interference or a malfunctioning electronic chip.

If the fob has been in a pocket which has endured extreme trauma, like being dropped on hard floors or being washed in the washing machine the fob may not be capable of communicating with the car's Body Control Module (BCM). The BCM is a security system which will only accept signals from genuine keys.

It is necessary to replace the fob in case this occurs. A professional locksmith can handle the entire replacement process including programming a new one for your 500. They can even offer a clone fob that works the same as the original (and costs only one-third of the cost).