How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is one of the most stylish and elegant mini cars on the market. Its interior is of higher quality than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's keyfob does much for you. It can lock and unlock your vehicle remotely. It also includes a mechanical key that you can use in the event the battery of your fob goes out.

Dead Coin Battery

Key fobs allow drivers to lock their cars and then start them, without having to insert an actual key into the ignition. It works by sending radio frequency signals which communicate with the computer onboard of the vehicle.

The battery in the keyfob is responsible for communication. It will eventually wear out, and the battery will need to be changed. Depending on the model of your Hyundai key fob, it may or not display a warning before the battery dies. Keep a spare keyfob handy for your side to replace the battery promptly when it wears.

The key fob has to be reprogrammed for the vehicle once the new battery is installed. This can be done using the Hyundai Digital Key app or an OBDII-based scanner, but it's typically easier to do at your Reno home. To do this, follow the instructions in the owner's manual or look on YouTube for "how to open and replace the Hyundai key fob battery." Be sure you record the old battery's number or take a photograph of it prior to removing it.

Once the key fob is changed, it should work again. If it isn't working you'll have to go to a dealer for a replacement hyundai key fob or contact locksmith. They will have the experience and tools to fix the issue.

Water Damage

A key fob is an excellent piece of technology that allows you to lock your car from the safety of your home, to roll down the windows from outside and even start your vehicle. It is not indestructible and will eventually wear out with normal use. Fortunately, the process of replacing the battery of a hyundai i10 key fob (http://dnpaint.co.kr/bbs/board.php?bo_Table=b31&wr_id=1235423) battery is surprisingly simple and cost-effective.

Dropping your key card in an puddle, a pool or even the washing machine isn't unusual and can be rescued, but only if you act swiftly. Water isn't a good mix when it comes to electronics and a wet key fob can cause many issues, such as corrosion, short circuits and even complete failure.

The first thing to do is to try to get as much water out as possible. Shake any visible moisture out by flipping the fob. You can also employ a hairdryer or set it on the radiator to speed up drying. After you have removed as much moisture as you can, consider placing the fob in a place that is cool and dry where it will continue to dry for a couple of days.

The next step is to remove the fob and remove the old battery. The majority of Hyundai i10 keys are powered by the same battery type as many quartz watches, and are very easy to change. Once you've replaced your battery, be sure to capture a picture or take an outline of how it's placed prior to closing up the fob.

Poor Battery Contact

It's possible that your key fob's battery is wearing out. This is a very common problem. Usually, the remote will start to exhibit signs of trouble before it completely fails. Make sure that the metal retaining clips are tight and do not have any corrosion on them. If so, make use of a wirebrush and battery cleaning solution to clean them. Make sure you use a button-cell that has the same voltage, size, and specification as the original.

It may also indicate that your alternator, which is the part that charges the battery while the engine is running, isn't working properly. An alternator that is not working properly can drain the battery quickly and cause the warning light to switch on.

You can determine if the Hyundai is affected by a simple voltage test. If the battery is functioning properly it's possible the issue is on the circuit board or some other component of the key fob. Press an incredibly small metal button or tab on the front or the back of the key fob to unplug it. After you take off the cover, you can insert a new CR2032 battery, making sure that all the connections are in contact.

Reprogramming

Hyundai offers keyless entry in several of its models. This makes traveling between Littleton and Parker, CO, easier than ever. You can use an electronic remote to start your car, unlock the doors, and lock them. But it's not impervious to destruction and a broken fob can cause issues. If your Hyundai keyfob fails to function it may be necessary to reprogramme it so that it works with your vehicle.

First, you must remove the battery. The button cell battery is usually found inside a plastic tab. If you are able to open the tab and replace the battery, make sure to use the same size and voltage as the old battery.

Once the battery has been replaced, close up the tab and replace the retaining clips. Test the key fob a second time to make sure it still works.

If the key fob still not working, you may need to contact an expert locksmith or dealer. A dealer or locksmith can cut a new key and remote for you, and can also program the key to work with your car. They usually charge a fee to do this, but it's well worth the investment if your Hyundai key fob to function as it did before. They can also assist you to identify the most suitable Hyundai key fob for your requirements.