Double Glazing Door Lock Repairs

Are your uPVC door or window mechanism broken? Maybe the window or door handles aren't aligned properly or are hard to use.

You'll be wasting energy in the event that your double-glazed doors fail to perform as they should. This increases the chance of burglary. Owen the Locksmith can repair your door lock for an affordable price.

Snapped Key

When a key snaps off within a lock, it could be incredibly difficult. This can also be a security risk in that it can make you vulnerable to burglars if your door does not lock. There are a few quick fixes you can try to repair the issue and get your door working again.

Be sure to remain calm. If you get scared and start poking around wildly you could end up pushing the damaged piece of the key deeper into the lock, which could make the situation even more difficult.

Then spray WD-40 or a different penetrating oil into the lock to aid in making the broken piece to slide out more easily. You can also use the screwdriver to break any pieces stuck. If you have a chunk of the key that's stuck, grab it with the help of a paperclip or any other thin metal object and pull it. Both methods work, but be very careful not to push the broken piece of the key even further into the keyway.

Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these, you can bend a hook with needle-nosed pliers. Finally, you can use a pair of tweezers grab and pull out the last bit of the broken keys.

If you cannot remove the broken key piece then you can use a lock deicer. This is usually available at most hardware stores, and it works by freezing any moisture or ice that may be inside the lock.

If none of these methods are working, it might be the time to contact locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are simpler to operate. Book a double glazing repair with us online or give us a call to discuss your needs.

Broken Cylinder

A broken cylinder can pose a serious security risk. Luckily, it's an easy repair for professional locksmiths to complete. To repair the cylinder, locksmiths must tap it. This can be accomplished with the hammer or other tool. However, the most effective method is to make use of a wire or a long match. Then, position the end of the match or wire near the keyway. The locksmith will then strike the lock to break it. This is superior to using a hammer that could harm the lock.

Overheating is the primary cause of cylinder heads cracking. This can occur when the block and cylinder head are made of different metals such as cast-iron and aluminium. When different metals are heated and cool at different rates, it can create hotspots in the local area that expand faster than the rest of the head of the cylinder, leading to cracks.

Another reason that could cause cracks in cylinders is corrosion. If the cylinder block and head are not maintained properly they could be corroded or rust, which can cause them to expand more than they would normally. This could lead to cracks in the future.

If your uPVC window or door lock is rigid and requires a lot more pressure to turn it could be due to a variety of causes. A malfunctioning locking mechanism, misalignment or a worn handle are common causes of this issue.

This is a simple and affordable fix that the majority of double glazing owners can do. A professional locksmith is able to solve the issue within one hour of arriving at your property. They can fix the locking mechanisms, or replace the window handles and change the gearboxes based on your particular requirements. A professional locksmith can always advise you on the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security TS007 euro cylinders that will add an extra layer of protection against burglars. This is a small cost to pay for the peace of mind that comes with knowing your uPVC doors are secure.

Broken Handle

Window handle locks are complex mechanisms that become less effective with time and use, so it's no surprise that they sometimes break. If yours is damaged, it can be difficult to identify the cause of the problem and make sure you fix it properly.

The issue could be in the internal locking mechanism or the latch, fixing the broken handle will increase your uPVC double glazing door's security as well as help you to stop drafts. It could be costly to replace or repair your handle incorrectly and it can also damage the frame and lock of your door.

Screwdriver Open the window, loosen the screw holding the handle. The screw should be on the inside face of the back plate, normally concealed by a screw cover for aesthetic reasons. Be careful not to lose any of the internal components inside the handle, for example the plates or levers that are on the opposite side of the spindle. Ideally, keep them in the same place so you can replace them again when needed.

Then, turn the handle until it's 90 degrees to the window frame and loosen the screw at the back of the handle that holds it to the internal spindle by using another screwdriver. Once this is released, you'll be able to pull the handle off and take out the broken spindle. Replace it with a brand new spindle, ensuring that it's the same length (you can buy them on the internet or in hardware stores). Securely screw it into place. Be careful not to overtighten as this could cause damage to the handle or the window doctor Near me frame.

Close the handle and try it. The hope is that it will function smoothly and you'll be able open your window once more.

Make sure to check that your uPVC window is shut properly when you're working with the handle. If they're not closing properly then you may experience damp and draughts inside your home as in addition to compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break rather than the handle. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that acts as an locking device within the window frame. The handle is attached to a rod in the centre that triggers a set of mushroom-like locking cams, these lock into window frame keeps. If the dead latch mechanism does not open after the handle is turned, it's likely the spindle has been damaged. This could be a frustrating problem.

Luckily, there are ways to remedy this situation. A skilled locksmith can quickly and effectively fix the issue. A professional locksmith will be able disassemble the window's handle using a tool to remove the wheel portion that houses the spindle. This is done without damage to the handle or window frame.

After removing the wheel, the technician can examine the spindle and determine the reason for its break. This involves disassembling the spindle and examining every component, observing any wear or damage. This procedure is usually done in a clean, well-lit room by highly skilled technicians.

Next, clean the damaged spindle. This will help remove any dirt or debris which may be obstructing it from functioning normally. The spindle may be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is comparable in size to the original. Then, he will drill matching holes into both pieces. This will ensure that the spindle is perfectly matched with the handle.

If the spindle that is damaged is beyond repair, it may be necessary to replace it entirely. Home centers sell generic replacements, but if the design of your window is unusual then it is necessary to find a woodworker or cabinet maker who can duplicate the exact model for you. Once the spindle has been installed, it is connected to the handle. The screw holes on the handle with the screws that are already in the frame. Once the new handle is firmly in place, you'll be able to operate your uPVC window.