Double Glazing Door Lock Repairs

Is your uPVC window or door mechanism faulty? Perhaps the handles on your uPVC windows or doors aren't aligned correctly or are difficult to use.

It is essential that the double glazed doors work smoothly, otherwise you'll be wasting energy and increase the likelihood of burglary. Owen the Locksmith can fix your door lock at an affordable cost.

Snapped Key

If a key breaks in a lock, it can be extremely difficult. This can also be a security risk because it could expose you to an intruder if the door is not locked. There are a few easy fixes you can make to repair the issue and make your door work again.

Be calm. If you panic and start doing a lot of fumbling around you could end up pushing the broken piece of the key even further into the lock, which could make the situation much worse.

Spray WD-40 or another penetrating oil, into the lock. This will help the broken piece emerge more easily. You can also make use of a screwdriver to break up any stuck pieces that might be hindering the flow. If you have a part of the key that is stuck then grab it using a paperclip or another thin metal object and pull it. Both of these methods work well, however, be careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have any of these, you can bend a hook using needle-nosed pliers. You can also use a pair tweezers to grasp and pull out the last piece of broken keys.

If you are unable to remove the broken piece of key then you can use a lock deicer. It's available at most hardware stores and works by freezing any moisture that may be present in the lock.

If none of these methods are working then it's probably time to call locksmith. Fitlocks experts can solve problems like broken handles and broken keys with uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms so that they are more easy to operate. You can book an appointment online for a double-glazing repair or call us to discuss your needs.

Broken Cylinder

A damaged cylinder can pose a serious security threat. A locksmith professional can fix the cylinder. To fix the cylinder locksmiths must tap it. They can do this using the hammer or any other tools, but the most effective way is to employ an extended match or piece of wire. Then, place the end of the match or wire in the keyway. After that, the locksmith can strike the lock and break it open. This is much better than using a heavy hammer, which could harm the lock.

Overheating is the main cause of cylinder heads cracking. This can happen when the block and cylinder head are made from different metals, such as cast-iron or aluminium. Different metals can heat up and cool off at different rates. This can cause localised hotspots to expand more quickly than the rest.

Corrosion is a different reason for cylinder fractures. If the head and block of the cylinder are not maintained properly they may rust or corrode, which can cause them to expand faster than anticipated. This can cause cracks over time.

If your uPVC door or window lock is brittle or requires an enormous amount of pressure to turn, it can be caused by several things. A faulty locking mechanism, misalignment, or an old handle are the most common causes of this issue.

Fortunately, this is an easy and cost-effective fix for the majority of homeowners with double glazing. A professional locksmith is able to solve the issue within one hour of arriving at the property. Depending on your needs they will be able to replace the locking mechanism, replace the window doctor near Me handles, and change the gearboxes. A skilled locksmith will always be able to inform you of the most cost-effective option for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders, which provide an additional security layer from burglars. It is a small cost to get the peace of mind that comes from knowing your upvc repair door is secure.

Broken Handle

It's not surprising that window handle locks may break. They are equipped with complex mechanisms that become less effective over time. If yours fails it may be difficult to identify the cause of the problem and make sure that you repair it correctly.

Fixing the broken handle, regardless of whether it's the internal latch or the locking mechanism, will improve the security of your uPVC door and stop draughts. It is costly to replace or repair your handle incorrectly and it could also harm the frame and lock of your door.

With the window open then loosen the screw that holds the handle using a screwdriver. This should be located on the inside face of the back plate, which is usually concealed by an aesthetically pleasing cover for the screw reasons. You should not lose any internal components of the handle such as the levers and plates on either side. Keep them in the same arrangement so that it is easier to replace them if needed.

Then, using an additional screwdriver, loosen the screw that connects the handle with the spindle in the back. Once this is released, you'll be able to pull the handle off and take off the damaged spindle. Replace it with a brand new spindle, ensuring that it's the same length (you can buy them on the internet or at hardware stores). Screw it into the frame. Do not overtighten the screw as this can cause damage to the handle and window frame.

Ensure the new handle is correctly fitted, then close and test the handle. It should function smoothly and you'll be able to open your window after a few times.

Don't forget to double-check that your uPVC window is closing properly when you're working with the handle. If they're not closing properly, you could experience damp or draughts inside your home. Also, you could be compromising the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of your window frames to ensure that they close properly.

Broken Spindle

It is often the case that the spindle inside the handle is broken, not the handle itself. This is particularly common in uPVC tilt and turn windows. These windows require a handle which is a lock mechanism that is located in the window frame. The handle is connected to a centre rod that in turn activates mushroom-like locking cams, these locks are inserted into the window frame. If the dead latch mechanism is not able to open after the handle is turned, it is likely the spindle is broken. This can be a problem that is frustrating.

There are ways to fix this problem. A good locksmith will be able to quickly and effectively address this problem. A professional locksmith can disassemble the handle of the window by using a tool to take out the wheel from the area where the spindle is located. This can be done without causing any damage to the handle or causing other damage to the frame of the window.

After removing the wheel, the technician can examine the spindle and determine the reason for its break. This involves breaking down the spindle into its component parts and carefully recording their general condition as well as any specific areas of damage or excessive wear. This process is typically done in a clean, well-lit room by skilled technicians.

The next step is to clean the damaged spindle, this will remove any dirt or other debris that might be obstructing its normal operation. After this the spindle is cleaned, it can be repaired or replaced. If the technician is replacing the spindle it is possible to use a dowel that is the same size to the original. Then, he will make holes in the same way into both pieces. This will ensure that the new spindle has an exact fit with the handle.

If the damaged spindle can't be repaired it may need to be replaced entirely. Home centres sell generic replacements but if the style of your window is unique then it will be necessary to contact a wood worker or cabinet maker who can make the exact model for you. Once the new spindle has been installed it can be fitted to the handle by lining up the screw holes on the handle with the frames existing screws. Once the new handle is firmly in place, you'll be able to operate your uPVC window.