Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they don't get rusty or decay.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home, and could even be fatal. It is essential to make sure that your windows are in good condition.

Single-pane windows are relatively simple to replace, and they typically fit into frames that were previously in use very easily. However, if you have double pane windows that are held in place by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this case, it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you're planning to attempt to remove the window panes by yourself, it is essential to wear the appropriate safety equipment, including thick gloves and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric and not onto the floor and could be trampled.

Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to prevent drafts and water from entering the property until a professional can come out and fix the window repair. This will also act as a barrier, deterring any intruders to gain access into your home. If the gap is particularly large, you might think about a security door that has an integrated window repairs near me, as this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber windows made of sash. However, over time they may be afflicted by a variety of problems including sliding. A window that is sagging can cause problems with light, draughts or even security. It's important to take action immediately if you notice your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window which is sagging. To do this, you'll have to open the window so that you can get to the frame. After that, using an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, close the window and check for fit. If you're satisfied with the fit, you can tighten the screws to ensure they remain in the right place.

If you are unable to reposition the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loose their elasticity. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

UPVC handles can also loosen. This is often caused by screws that have loosened over time, but it can be caused by the handle mechanism wears out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. The first step is to close the window and perform a test to ensure that it fits. The corners of the sash must be aligned with the casing joint. If it doesn't then you can use a screwdriver to loosen the handle and then return the mechanism to its original position.

3. Water Leaks

It is important to take action if you get up each morning to find a smoky wall and floors that are wet. Windows that leak water do can not only cause degrading of the structure of your home but also undermine your efforts to control the temperature within your home. The most common cause for leaking uPVC windows is that the sealant around the frame has been damaged or not present.

This is a simple fix that can be accomplished by any DIYer who has the ability. Based on the severity of the problem the caulking that was used up might need to be removed before a new layer can be applied. It is important to remember that when it is about uPVC window repairs you should avoid the temptation to "over-caulk' as this will only make the area harder to clean and can reduce the efficiency of your energy.

It is essential to ensure that the drainage holes are free of debris and that the sill pan is placed properly so that it drains away from the window. In more serious situations, you may need to think about replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. This mold thrives in damp environments and can quickly spread across the home.

It is also important to note that if the leak is coming from between the glass of your double glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open in a breeze It could be hinges that are at the fault. They can be easily repaired by any DIYer who is skilled and can usually be done within a few minutes.

Most households in the UK will have top-hung or side-hung uPVC windows that use hinges and, like all mechanical parts, they are susceptible to wear and tear over time. It is very easy to change the hinges on a window but it's much easier if someone else helps hold the frame.

It is also important to verify that the uPVC hinges are opened and closed in the right direction. You can do this by checking for the arrows on each hinge, this shows which way the window should open.

The problem with the hinges on windows could be caused by improperly opening the window in a particular manner or because of improper installation in the factory. This can often be resolved by sending us a photo through our website and we will be pleased to offer you advice.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We suggest using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also stop corrosion and reduce the risk of sticking. This should be done at least every year. WD40 or other solvent-based oils are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a few different things. First, the hinges because of wear and tear, can become misaligned, this causes an opening to appear where the sash meets the frame. If they're beyond repair, it could be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge side of the window and can also become misaligned, again it is feasible to give them a good clean, but in certain cases, it may be necessary to get them replaced.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping is a good way to stop draughts. Another alternative is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures, and also lessen the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler, which can be hung over your window sill. They will help keep cold air out and keep your home warm and cozy!

With a little maintenance and repairs your windows made of upvc will provide an excellent level of security and insulation for your home. It is crucial to keep in mind that all windows will eventually wear out and it is more cost-effective to replace them rather than repair them. So, if you're having issues with your upvc windows, it's recommended to seek help from a professional immediately.