Reasons Your fiat 500 key cutting 500 Key Fob Won't Work

A key fob for fiat punto remote key Replacement 500 makes it simple to open doors and start your car. There are a myriad of reasons why the fob may stop functioning. This could be due to a dead coin-battery, water damage, receiver modules issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why the 500 key fob won't function is due to the battery is dead. Modern key fobs operate with a limited operating range, and should be within just a few feet of the vehicle in order to function. If you are far from your car and press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the coin cell battery (Part number CR2032) by a new one from a reputable brand like Panasonic, Fiat punto Remote key replacement Duracell, or Energizer. They are available at the local hardware store or on the internet.

After you've replaced the battery in the coin cell You can test it by standing next to your Fiat 500 and pressing the buttons. The car should blink its parking lights, and the key fob should operate the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it may have water damage that stops it from communicating with the receiver module in your car. Water damage can occur through a variety of methods, including a simple splash or submerging the key fob into saltwater at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work your fob may require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

While the fob has some rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the circuit board of the fob which causes it to short out and eventually end up dying. It's not a good thing to soak the fob in water, but don't give it up in the event that you accidentally drop it in water or fail to take it out of your pocket.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Test the fob afterward to verify if it's working. If the fob doesn't work then it might need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and not programmed for your vehicle You will need to replace it completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will require the key to be cut to match the car's ignition. They'll also need to reprogram the fob to the system of your car. This is a fast and cost-effective process that can usually be completed the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob could stop functioning is that it's out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far from your vehicle it will not respond to your commands. It can be solved by moving it closer to your vehicle until it starts responding.

If your fob won't work after replacing the battery inside the coin, which is also called a "button", "watch" or "button" It could be due to an issue with the circuit board inside. Reprogramming your fob can resolve this issue. There are instructions on how to do this on the majority of vehicles by searching YouTube or reading the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension they could stop the battery from being seated properly, and this will cause your remote to malfunction.

In rare instances, the fob could be out of sync with your vehicle because due to hardware or software issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances it is possible that the software will require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin, the key fob may not be able to receive or transmit the signal due to interference. This can occur when the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob could not function because of a problem to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

There is a straightforward method to reset the 500's on-board system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computer system, which can help you get your key fob working again. If the problem persists you should speak with an experienced technician. They will be able to determine the exact cause of any problems.