Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they don't rust or rot.

It is crucial to wash and oil UPVC windows and doors regularly. This will help prevent costly repairs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and even be fatal. It is important to take the time to make sure that you are doing everything you can to keep your windows in good condition.

Single-pane windows are relatively simple to replace and will usually fit into the old frames very easily. If windows with double panes are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need to find some plastic spacers to assist the new pane to fit correctly into the window doctor frame.

If you are going to try to remove the glass panes yourself it is important to wear appropriate safety gear, including thick gloves and eye protection. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards fall on the fabric, not onto the floor and could be trampled.

Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from getting into the home until a professional is able to come out and repair the window. This also serves as an obstruction to prevent criminals from getting into your home. If the gap between the door and the window is substantial, you may want to use a security screen that also has an opening. This will give you the best of both.

2. Sagging

Upvc windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows with sash. Over time, they can be affected by a variety of issues that include sagging. A sagging window in uPVC can cause issues with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's important to act quickly to prevent the problem from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. First, you'll need to unblock the windows so you can reach the frame. Then, using an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close your window and test it for fitting. If you're satisfied with the fit of the window, you can tighten screws to keep them in the right position.

If you can't reposition the hinges, you might require replacing the seal. As time passes, rubber seals lose their elasticity and dry out and cause them to loosen. It is important to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. Most often this is due to screws that have become loose over time. However, it could occur because the handle mechanism has worn out. It's relatively simple to fix a loose uPVC handle. First, you'll need to shut the window and perform an initial fitting. The joint at the corner of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle and then return the mechanism to its original position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it's crucial to take action. The leaks of water through windows could cause structural damage to your home and hinder your ability to control the temperature inside your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be done by anyone who is a DIYer with the skills. Depending on how severe the issue is, old caulking may have to be removed. It is essential to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk in order to make the area harder to clean and can reduce the efficiency of your energy.

Make sure that the drainage holes are free of debris in them and that the sill pan is properly angled to allow the water to drain from the window. In more extreme instances, you may need to replace the window.

Moldy sills and rotten ones are another sign of water leakage. This is a fungus that thrives in damp conditions and can quickly spread throughout the house.

It is also important to keep in mind that if the leak originates from the glass of your double glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sagging. A uPVC specialist can easily solve this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and open with a breeze it could be hinges at the fault. Any competent DIYer can replace these in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that use hinges and window Doctor Near me like any mechanical part they will wear out over time. It is very easy to change the hinges on a window but it's much easier if someone helps hold the frame.

Make sure that the uPVC hinges are open and closed in the correct direction. You can do this by looking for the arrows on each hinge. This indicates which way the window should open.

The issue could be caused by opening the window incorrectly or due to a poor installation in the factory. This can often be resolved by sending us a photo through our website and we will be pleased to offer you advice.

Regular lubrication of hinges is also essential. Applying an engineering lubricant that is light to the hinges is a good method to accomplish this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the possibility of a window sticking and prevent corrosion. It is recommended to do this at least once a year. WD40 and other solvent based oils are not recommended because they will damage parts of your uPVC window doctor near Me.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different factors. The hinges can also become misaligned due to wear, causing gaps where the sash and frame meet. This can be easily repaired by giving them a good cleaning, but if they are beyond repair it could be necessary to have them aligned or replaced. The interlock may also become disaligned. It is located on the hinge side and might require to be cleaned. In certain instances it is possible to replace these.

The second most frequent cause of draughts is the window seals, these are susceptible to being worn out or damaged over time, and allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures and lessen the risk of draughts.

Another, and most effective methods to reduce the draughts in your home is to use a draught excluder. These are typically fabric tubes which are filled with a type of filler. They can be positioned on top of your windowsill. They will keep your home warm by blocking cold air.

The windows made of upvc repairs near me can continue to provide excellent insulation and security for your home with a little regular maintenance and repairs. It is important to remember that all windows eventually get worn out and it could be cheaper to replace them than to repair them. So, if you're having issues with your upvc windows, it is always recommended to seek help from a professional as soon as possible.