Repairs to uPVC Windows

uPVC is a great option for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to decay or rust as aluminum or timber.

It is crucial to wash and oil UPVC windows and doors regularly. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and may even be fatal. It is crucial to take the time to ensure that you are doing everything you can to ensure that your windows are in good repair.

Single-pane windows are relatively simple to replace and typically fit into frames that were previously in use very easily. However when you have double-pane windows that are held in place by internal beading, it will be more difficult to remove the existing panes and install new ones. In this situation you'll need source some plastic spacers that help the new pane to fit properly into the window frame.

If you plan to attempt to remove the window replacement panes yourself, it is essential to wear the proper safety gear that includes gloves with a thick layer of material and eye protection. You should also lay down a dropcloth before you begin working on the window panes, so that any shards fall onto the fabric and not on the floor and could be trampled.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional can come out and fix the window. It also acts as a barrier that will prevent any intruders to gain access to your home. If the gap between the window and the door is substantial, you may need to consider security screens that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. However, over time, they are susceptible to a range of issues like sliding. A window that is sagging can cause problems with light, draughts, and even security. It's crucial to act immediately if you notice your uPVC windows are sagging.

To fix a sagging window you can try to reposition the hinges. To do this, you'll have to open the window to get to the frame. After that, using a screwdriver, you can remove the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you have moved your hinges. If you are happy with the fit of the window, you can tighten screws to hold them in the right position.

If you cannot reposition the hinges, you might have to replace the seal. Rubber seals can dry out and lose their elasticity over time, leading them to loosen. If this happens, it's crucial to replace the seal as quickly as you can to ensure that your uPVC windows are waterproof and draught-proof.

uPVC handles may also become loose. Often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's a good thing that it's simple to fix the loose uPVC window handle yourself. First, you'll need close the window and perform an experiment fit. The joint at the corner of the sash must align with the joint on the casing. If it doesn't then you can use the screwdriver to loosen the handle. Then, turn the mechanism into position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and impact your ability to regulate the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant around the frame is either damaged or missing.

This is an easy fix that can be completed by any DIYer who has the ability. Depending on the severity of the issue the caulking used previously may need to be removed before a new layer can be applied. When it is time to uPVC repair, you should be careful not to over-caulk. This can make your window harder to clean and reduce its energy efficiency.

It is important to check that the drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious instances, you may need to think about replacing the window.

Other indicators of water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. This is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double-glazed window, it is more likely the issue is with the seal than the frame. It is also possible to be corrected by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open in a breeze it could be hinges at the fault. These are easily replaced by any competent DIYer and can usually be completed in a matter of minutes.

Like any mechanical part hinges are prone to be damaged over time. It is very easy to change the hinges on a window however it is easier if someone else helps you hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrow on each hinge. This shows which way the window should open.

The problem with the hinges on windows could be the result of incorrectly opening the window in a particular manner or because of inadequate installation at the factory. This can often be resolved by sending us a picture via our website and we will be happy to give you advice.

It is also essential to ensure that the hinges are lubricated regularly. This can be accomplished by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window operate and close more smoothly. It can also stop corrosion and reduce the possibility of sticking. The ideal time to perform this every year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a few different factors. The hinges can also become unbalanced due to wear, which can cause gaps between the frame and sash. These can be easily repaired by giving them good cleaning, but in the event that they are beyond repair it could be necessary to have them realigned or replaced. The interlock, which is located on the hinge side of the window, can also be misaligned, and again it may be possible to give them a clean but in certain cases, it may be necessary to have them replaced.

The next most common cause of draughts is the window seals. These can become worn down or damaged over time, and let air escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures, and reduce draughts.

Another, and most effective ways to reduce the draughts in your home is to use a draught excluder, these are typically made of fabric which are filled with a kind of filler. They can be put on the windowsill on top. These will keep your home warm by blocking cold air.

With a little regular maintenance and repairs windows made of upvc will provide an excellent level of security and insulation for your home. It is crucial to recognize that all windows have a life span and they may reach the point when it's more efficient to replace them than repair them. If you have any problems with your window made of upvc it is recommended to speak with a professional immediately.