Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. As opposed to aluminium and timber they do not get rusty or decay.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will reduce unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is important to make sure that your windows are in good condition.

For single pane windows, it is relatively easy to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. However when you have double glazing repair pane windows that are held in place by internal beading, it'll be more difficult to take out the existing panes and install new ones. In this case it is essential to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you're planning to try to remove the window panes yourself it is crucial to wear appropriate safety gear such as gloves that are thick and protective eyewear. It is also an excellent idea to lay down a dropcloth before you begin working on the glass so that any shards will fall on the fabric instead of onto the floor, where they could be trodden under and cause further damage.

Once the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from entering the property until a professional comes out and repair the window. It also acts as an obstacle to stop intruders from making their way into your home. If the gap is large, you may want to consider using an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash window. As time passes, they may be affected by a variety of issues that include sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. It's crucial to act as soon as you notice your uPVC windows are falling down.

Repositioning the hinges could help fix a window that is sliding. First, you'll need to unblock the windows to get at the frame. Then, remove both the top and bottom hinges using a screwdriver, and then adjust them counter-clockwise or clockwise. Close your window to check the fit after having relocated your hinges. If you are happy with the fit of the window, you can tighten screws to secure them in the right position.

If you are unable to reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause them to loosen. It is important to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles could also loosen. The majority of the time, this is caused by screws that have become loose over time. However, it can occur because the handle mechanism has worn out. Fortunately, it's easy to fix the handle of a window that is loose yourself. First, you'll need close the window and then perform an initial test to ensure that it fits. The corner joints of the sash must be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

If you awake to wet floors and damp walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home, and affect your ability to regulate the temperature of your home. The most common reason for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is an easy fix that can be completed by any DIYer who has the ability. Depending on the severity of the problem the old caulking may need to be removed before a fresh layer is applied. It is essential to remember that when it is about uPVC window repairs, do not be tempted to apply too much caulk in order to make the area harder to clean and could reduce the efficiency of your energy.

It is essential to ensure that any drainage holes are clear of debris and that the sill pan is placed correctly so that it drains away from the window. In more severe instances, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread throughout the house.

It is also important to note that if the leak is coming from between the glass of your double-glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open in a breeze, it may be the hinges that are at fault. They can be repaired by any DIYer who is skilled and can usually be done within a few minutes.

Like all mechanical parts hinges are prone to be damaged over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier if you have someone to help you hold the frame in place.

Check that the uPVC hinges are open and closed in the correct direction. You can check this by looking for the arrow on each hinge, this shows which way the window should be opened.

The problem with the hinges on windows could be the result of incorrectly opening the window in a particular manner or because of inadequate installation at the factory. This issue can be fixed by sending us a photo through our website and we will be more than happy to give you suggestions.

Regularly lubricating hinges is also essential. Applying an engineering lubricant that is light to the hinges is a good method to accomplish this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and reduce the risk of sticking. Ideally, you should perform this every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. First, the hinges because of wear and tear, may become displaced, which can cause a gap to form between the sash and the frame. If they are damaged beyond repair, it might be required to realign them. In addition, the interlock could also become disaligned. This is located on the hinge side and might require to be cleaned. In some cases it is possible to replace them.

The next common reason for draughts are the window seals. They are prone to wear or damaged over time, and let air escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures and decrease the risk of draughts.

One of the most effective ways to reduce drafts is to use an draught excluder. These are usually fabric tubes which are filled with a kind of filler. They can be put on the windowsill on top. They can keep your home warm by blocking cold air.

The windows made of upvc can continue to provide excellent insulation and security to your home by performing regular maintenance and repairs. It is essential to remember that all windows eventually wear out and it is more cost-effective to simply replace them than to repair them. If you have any problems with your upvc window you should consult an expert as soon as you can.