Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They don't decay or rust as timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, making it very hazardous and possibly fatal. It is important to ensure that your windows are in good shape.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. However when you have double-pane windows that are held in place by internal beading it will be more difficult to get rid of the existing panes and install new ones. In this case you'll need find some plastic spacers to help the new pane to fit properly into the frame of the window.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth prior to when you begin working on the glass, so that any shards fall onto the cloth instead of landing on the floor where they can be trampled upon and cause further damage.

After the glass has been removed from the window, it's best to seal the gap with some clear packaging tape or duct tape to stop water and drafts from entering the property until a professional comes out and repair the window. It also acts as a barrier, deterring any intruders from getting access to your home. If the gap is large, you may want to consider using an alarm door that comes with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash window. Over time, they can be affected by a variety of issues such as sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. It is crucial to act immediately if you realize that your uPVC windows are falling down.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to open the windows so you can access the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you've adjusted the hinges, close your window repairs and test it for fit. If you're satisfied with the fit of the window, tighten the screws to secure them in the right position.

If you are unable to move the hinges, you might have to replace the seal. Rubber seals may dry out and lose their elasticity with time, which causes them to loose their elasticity. If this happens, it's essential to replace the seal as fast as possible so that your uPVC windows remain watertight and draught-proof.

uPVC handles can also become loose. Most often, this is caused by screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. Fortunately, it's easy to repair a loose uPVC window handle yourself. You'll first need to close the window and window repairs do an initial fitting. The corner joints of the sash must align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and window repairs then return the mechanism to its original the position it was in.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it's crucial to take action. Windows that leak water do are not just a cause for degrading of the structure of your home but also hamper your efforts to regulate the temperature in your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by any DIYer who has the ability. Based on the severity of the issue the old caulking may need to be removed before a new layer of caulk is applied. It is essential to keep in mind that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk and then make the area more difficult to clean and can reduce your energy efficiency.

Check that any drainage holes do not have debris in them and ensure that the sill pan is properly angled to drain away from the window. In more severe situations, you may have to replace the window.

Mold spots and rotten sills are another sign of water leakage. This mold thrives in damp environments and can quickly spread across the home.

It is also important to remember that if the leak originates from the glass of your double glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with a breeze It could be hinges at fault. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical part, hinges can be damaged over time. It's very simple to change a window hinge however it is simpler if you have someone to help you to hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. This can be done by checking for the arrows on each hinge. This indicates which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window a certain way or due to improper installation in the factory. It is usually possible to fix the issue by sending us a picture on our website. We will be happy to give you suggestions.

It is also crucial to ensure that the hinges are lubricated on a regular basis. Applying an engineering lubricant that is light to the hinges is a great way to do this. We suggest using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It can also reduce the risk of a window sticking and prevent corrosion. This is recommended to be done at least every year. WD40 or other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by various factors. The hinges can also become misaligned due to wear, which can cause an opening between the frame and sash. If they are damaged beyond repair, it could be necessary to get them re-aligned. In addition, the interlock could be disaligned. This happens on the hinge's side and might require to be cleaned. In certain instances it might be necessary to replace these.

The seals may wear out or get damaged over time, allowing air escape. Replacing these with high-quality weatherstripping can help keep draughts at bay. Replace the windows made of upvc with low-emissivity glasses. This will help regulate indoor temperatures and lessen draughts.

Another, and most effective ways to cut down on the draughts in your home is to use an draught excluder. These are typically fabric tubes that are filled with some kind of filler. They can be positioned on the windowsill on top. These will keep your home warm by blocking out cold air.

With a little regular maintenance and repair, your upvc windows will provide a great level of insulation and security for your home. It is important to remember that all windows will eventually become worn out, and it could be more cost-effective to replace them rather than repair them. So, if you are experiencing issues with your Upvc windows, it's recommended to seek assistance from a professional as soon as possible.