Reasons Your fiat ducato replacement key 500 Key Fob Won't Work

A fiat 500 key cover uk 500 key fob is a convenient method to open the doors and begin the car. There are many reasons the key fob might stop working. It could be due to a dead battery or damaged receiver module, water damage issues, fiat 500x key fob programming or interference.

This listing is for a NEW replacement fiat 500X key fob programming Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob not working. Key fobs of today have an operating range that is limited and must be within a few inches of the vehicle in order to work. If you are far from your vehicle and you press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) with a new battery of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at the local hardware store or online.

After you've replaced the battery of your coin cell you can test it by standing next to your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should be able to operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module in your vehicle. Water damage can happen in a number of ways, ranging from the slightest splash to submerging the fob salt water at the beach. If you think your fob was exposed to water, put it in a bag of rice to draw out the moisture. If that doesn't work your fob is likely to need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short, and eventually cease to function. It's not good to soak the fob in water but don't give up in the event that you accidentally drop it in water or forget to take it out of your pants pocket.

Take the battery off first. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Check the fob to determine if it's working. If the key still doesn't work, fiat 500x key Fob Programming it might need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key you have is older and is not programmed for your car it is necessary to replace it completely. A professional locksmith in the automotive industry can carry out this simple task. The locksmith must cut the key to match the ignition of your vehicle. They'll also need to reprogram the fob for the system of your car. This is a cheap and fast process that can be completed the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop functioning is that it's out of range. The remote has a maximum range of 30 feet, which means in the event that you are far away from your vehicle it won't respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.

If your fob won't work after you replace the coin battery, also called a "button", "watch" or "button" It could be a problem with the circuit board inside. Reprogramming your fob can resolve this problem. There are instructions on how to do this for the majority of vehicles by searching YouTube or reading the owner's manual.

It is possible to replace the metal clips that keep the coin battery. If they lose tension it can prevent the coin battery from being properly seated and can result in the malfunction of your remote.

In rare instances, the fob may be out of connection with your vehicle as a result of hardware or software problems. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases they might need to reinstall the software in your body control module, as well.

Interference

Interference can also cause the key fob to be unable to receive or transmit the signal. This could occur if the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not function because of a problem to the buttons, water damage or damage to the internal chips.

If the key fob failed to work one day in the middle of the night and you've tried everything you can do at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands, which are then interpreted by the vehicle.

There's a simple method to reset the 500's internal system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electric current, and also restart the computer in your car. This can help get your key fob to work again. If the issue persists, you should seek out an expert technician. They will be able to identify the root cause of your problem.